Results 51 to 60 of about 89,598 (261)

Analysis of sound field in dominicans’ church in Cracow

open access: yesArchives of Acoustics, 2014
This publication presents the results of sound field analysis: simulation using ray method, finite element model below 200 Hz and real reverberation time measurements in band 125–8000 Hz, executed in Dominicans’ church in Cracow. Effects of calculations
Magdalena Plewa
doaj  

A Confined Flow over a Cylinder by the Finite Element and the Finite Difference Methods [PDF]

open access: yesEngineering and Technology Journal, 2011
The Finite element and the finite difference methods were applied to a confined flow over a cylinder. The values of velocity potential (F), the stream function (Y) and the velocity distribution are calculated by using a computer programs achieved by the ...
Ahlam Sadir Mohammed
doaj   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

open access: yesAdvanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm   +3 more
wiley   +1 more source

Convergence of Adaptive Finite Element Methods [PDF]

open access: yesSIAM Review, 2002
The authors consider the use of adaptive finite element methods. They construct an algorithm, which converges linearly and which does not involve preliminary mesh adaptation. They give the results of a number of numerical experiments and point out the possibilities associated with higher order elements and saddle point problems are also discussed.
Morin, Pedro   +2 more
openaire   +2 more sources

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

open access: yesAdvanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares   +3 more
wiley   +1 more source

Cut finite element methods

open access: yesActa Numerica
Cut finite element methods (CutFEM) extend the standard finite element method to unfitted meshes, enabling the accurate resolution of domain boundaries and interfaces without requiring the mesh to conform to them. This approach preserves the key properties and accuracy of the standard method while addressing challenges posed by complex geometries and ...
Erik Burman   +3 more
openaire   +3 more sources

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

open access: yesAdvanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan   +5 more
wiley   +1 more source

An Optimal Adaptive Finite Element Method [PDF]

open access: yesSIAM Journal on Numerical Analysis, 2005
The Dirichlet problem in a polygonal domain \(\Omega\) in \({\mathbb R}^2\) for a second-order elliptic equation with disconinuous coefficients is considered. The finite element methods on triangulations of \(\bar\Omega \) are investigated and the main purpose of the paper is to generalize some published results dealing with convergence analysis of ...
openaire   +2 more sources

Home - About - Disclaimer - Privacy