Results 51 to 60 of about 686 (227)

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Development of Table-on-Table-Type Five-Axis Machining Center: New Structure and Basic Characteristics

International Journal of Automation Technology, 2011
The demand for five-axis machining centers has been increasing rapidly, as companies seek “intensive processes” and “high accuracy.” However, it is generally more difficult for five-axis machining centers to achieve the same or higher accuracy than three-axis machining centers since it is necessary to have two more rotary feed axes besides the three ...
Naoshi Takayama, Hidehito Ota, Kensuke Ueda, Yoshimi Takeuchi   +3 more
openaire   +1 more source

Enhancing Fatigue Crack Growth Resistance in Heterostructured Aluminum Bimetals by Tailored Interface Design

Advanced Engineering Materials, EarlyView.
Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath, Philip Manuel Pohl, Heinz Werner Höppel   +2 more
wiley   +1 more source

Identification of Geometric Deviations Using Simultaneous Five-axis Control Technique in Five-axis Machining Centers with Double Pivot Spindle Head

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C, 2006
This study was conducted for developing the testing methods by means of simultaneous five-axis motion in five-axis controlled machining centers with a double pivot spindle head. In this paper, the five axis motion was simulated considering the measurement by a ball bar system and the relative distance change between both balls of the table side and the
TSUTSUMI, Masaomi, YAMAMOTO, Ken, SAITO, Akinori, DASSANAYAKE, K. M. Muditha, MIKAMI, Shigetaka   +4 more
openaire   +1 more source

Foundational Machine‐Learning Interatomic Potential for Simulating Chemically Complex Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
We apply a foundational machine‐learning interatomic potential based on the graph atomic cluster expansion (GRACE) to simulate the commercial Ni‐based single‐crystal superalloy CMSX‐4. Hybrid Monte‐Carlo/molecular dynamics sampling resolves short‐range order in the γ phase and L12 sublattice occupancies in the γ’ phase and connects them to stacking ...
Aditya Vishwakarma, Sarath Menon, Fritz Körmann, Thomas Hammerschmidt, Ralf Drautz   +4 more
wiley   +1 more source