Results 51 to 60 of about 2,744,429 (208)
Spatiotemporal control over cell behavior within bioprinted constructs remains a key challenge in biofabrication. Volumetric bioprinting using multi‐wavelength light sources permits to activate light‐sensitive intracellular proteins as well as optogenetic gene and protein expression circuits in bioprinted cells, in addition to enabling fast printing of
Davide Ribezzi +14 more
wiley +1 more source
A novel selective laser sintering and graphitization (SLSG) 3D printing technology enables unibody fabrication of compacted insulating structures and conductive circuits in fluidic‐integrated wearable electronics through adaptive photonic modulation.
Li Zhang, Wing Cheung Mak
wiley +1 more source
3D shaping of Ni1‐xFexCo2O4 spinel electrocatalyst to form high aspect ratio nanorods, made of 25 nm grain size particles and directly grown on Nickel felt, is proposed to improve the performance of industrial catalysts based on group‐VIII transition‐metal oxides.
Ataollah Niyati, Ombretta Paladino
wiley +1 more source
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina +5 more
wiley +1 more source
Collision‐Resilient Winged Drones Enabled by Tensegrity Structures
Based on structures of birds such as the woodpeck, this article presents the collision‐resilient aerial robot, SWIFT. SWIFT leverages tensegrity structures in the fuselage and wings which allow it to undergo large deformations in a crash, without sustaining damage. Experiments show that SWIFT can reduce impact forces by 70% over conventional structures.
Omar Aloui +5 more
wiley +1 more source
A Soft Robotic Fish With a Dielectric Elastomer Actuator Body and Negative Stiffness Spine
This work introduces a bio‐mimetic soft robotic fish driven by fiber‐reinforced dielectric elastomer actuators integrated as its body. By prestretching this active skin against a flexible spine, a negative stiffness system is created, enabling large‐amplitude bending.
Markus Koenigsdorff +4 more
wiley +1 more source
ABSTRACT The demand for off‐the‐shelf biocompatible bone substitutes has driven the development of numerous independent in vitro technologies to generate products resembling physiological tissues. Due to technical challenges and overly simplified cultivation approaches/niches, the end‐products are often uniformly shaped and inferior to native bone ...
Franziska Braun +10 more
wiley +1 more source
The fabrication of wide‐bandgap perovskite thin films via green solvents integrated with inkjet printing is developed. Controlled crystallization of the perovskite layer is achieved by optimizing ink formulation and additive engineering, enabling power conversion efficiencies above 17% for single junctions and 28% for perovskite/silicon tandem solar ...
Uma Kousalya Dangudubiyyam +12 more
wiley +1 more source
Local Heat Transfer Measurements on a Rotating Flat Blade Model with a Single Film Hole [PDF]
An experimental study was performed to measure the heat transfer coefficient distributions on a flat blade model under rotating operating conditions. A steady-state thermochromic liquid crystal technique was employed to measure the surface temperature ...
Tao, Zhi +8 more
core +1 more source
A novel exercise‐inducible myokine acidic ribosomal protein P2 (RPLP2), initially identified from human trials, is presented here, whose circulating levels negatively correlate with clinical anxiety severity. Muscle‐derived RPLP2 enhances hippocampal ribosomal assembly and adult neurogenesis to rescue stress‐induced anxiety deficits.
Peiyu Luo +18 more
wiley +1 more source

