Results 71 to 80 of about 5,491,792 (284)

Metastable Polymers for Circular 3D Printing

Advanced Materials, EarlyView.
3D‐printed polymers are usually permanent and hard to recycle. Here, metastable polymers are designed to fall apart on demand. A chemical trigger unzips the printed material back into its original building blocks within minutes at room temperature.
Johannes Markhart, Philipp Mainik, Eva Blasco   +2 more
wiley   +1 more source

Response characteristics of methane–air and propane–air premixed flames to sinusoidal oscillations in equivalence ratio (Effects of Lewis number and preferential diffusion)

Journal of Thermal Science and Technology
Flames propagate in mixture flows with inhomogeneous concentration distributions in practical combustors, such as gasoline direct-injection engines and gas turbine engines. Clarifying the effect of fuel-type differences on the response characteristics of
Yosuke SUENAGA, Hideki YANAOKA, Shohei SEO, Komei NIWATA   +3 more
doaj   +1 more source

Turbulent Flame Geometry Measurements in a Mass-Production Gasoline Direct Injection Engine

Energies, 2020
Direct optical access to the combustion chamber of a gasoline direct injection (GDI) engine provides extremely valuable information about the combustion process.
Manfredi Villani, Phillip Aquino
doaj   +1 more source

Toward Pore‐Engineered 3D‐Printed Materials for Sorption Water Harvesting, Interfacial Evaporation, and Radiative Cooling

Advanced Materials, EarlyView.
Water harvesting, radiative cooling, and interfacial solar evaporation are fundamentally governed by coupled heat, mass, and light transport processes. These processes are mediated by pore architecture, including pore size, connectivity, and hierarchical organization.
Dejan J. Trajkovski, Higgins M. Wilson, Abdallah Y. M. Ali, Jiaxing Xu, Ruzhu Wang, Primož Poredoš   +5 more
wiley   +1 more source

Characteristics of biogas-oxygen micro counterflow diffusion flames

Nihon Kikai Gakkai ronbunshu, 2015
The characteristics of biogas-oxygen diffusion flames were experimentally investigated using small counterflow burners, where the apparent equivalence ratio was set to unity.
Satoshi KADOWAKI, Go OKUMURA, Ryutaro NUMATA, Toshiyuki KATSUMI   +3 more
doaj   +1 more source

Strong Coupling in Bulk Nanoplasmonic Nanoplatelet Perovskite Scintillators

Advanced Materials, EarlyView.
A bulk scintillating nanocomposite is engineered from CsPbBr3 nanoplatelets and Ag nanocubes to support exciton–plasmon strong coupling under X‐ray excitation. The resulting hybrid polaritonic states appear directly in radioluminescence, opening a route toward polariton‐enabled scintillator design beyond conventional Purcell enhancement.
Michal Makowski, Dominik Kowal, Anna Pniakowska, Kamil Misztal, Mohanad Saadeldin Eid, Joanna Cybinska, Winicjusz Drozdowski, Benoit Mahler, Christophe Dujardin, Detlef Hommel, Liang Jie Wong, Dennis Schaart, Sergio Brovelli, Muhammad Danang Birowosuto   +13 more
wiley   +1 more source

Radiative Thermal Management for Extreme Environments: Mechanisms and Design Strategies

Advanced Materials, EarlyView.
In this review, we discuss the fundamental mechanisms of radiative cooling and solar heating, material and structural design strategies, hybrid approaches integrating additional heat transfer pathways, and durability‐oriented designs addressing environmental stresses.
Hyung Rae Kim, Haeseong Kim, Joo Hwan Ko, Gil Ju Lee, Dae‐Hyeong Kim, Young Min Song   +5 more
wiley   +1 more source

Experimental investigation of fundamental flame characteristics, N2O and NF3 decomposition, and NOX formation in hydrogen/methane diffusion flames

Case Studies in Thermal Engineering
In this study, the thermal decomposition characteristics of high-global-warming-potential (GWP) greenhouse gases (N2O and NF3) and the associated NOX emission behaviors were experimentally investigated under methane/hydrogen diffusion flame conditions ...
Sumin Song, Yu Jeong Kim, Sung Hwan Yoon, Jungho Hwang, Dae Geun Park   +4 more
doaj   +1 more source

Adsorbent Materials for Hydrocarbons Removal by Geopolymerization of Halloysite Clay Nanotubes Filled Within Chitosan Matrix

Advanced Materials Interfaces, EarlyView.
Alkaline activation of halloysite clay nanotubes embedded in a chitosan matrix converts bionanocomposite films into porous geopolymeric materials with enhanced adsorption capacity toward hydrocarbons in both vapor and aqueous phases. The improved adsorption performance was demonstrated by the efficient capture of dodecane vapors and phenol from water ...
Alessandro Lo Bianco, Marta Giuseppina Ebbreo, Giuseppe Cavallaro, Martina Maria Calvino, Yafei Zhao, Simonpietro Agnello, Giuseppe Lazzara   +6 more
wiley   +1 more source

Flame Characteristics of Gasoline and a Water-in-Gasoline Mixture under a Controllable High-Temperature Thermal Atmosphere. [PDF]

ACS Omega, 2022
Wu Z, Yu Y, Xie W, Liu Y, Hou X.
europepmc   +1 more source