Results 171 to 180 of about 52,072 (307)
Chemie Ingenieur Technik, EarlyView.All energy matters Let us broaden the discussion on solutions to climate change. Greenhouse gases have upset the delicate equilibrium of the Earth's energy balance. Consequently, all sources of heat affect the temperature of the Earth. Although the amount of additional heat generated by humans is a fraction of that produced by the sun, it is generated ...
Martin Bertau +2 more
wiley +1 more source
Influence of Surface Modification of Fly Ashes on the Fire Behavior of Polyamide 6. [PDF]
Polymers (Basel)Batistella M +3 more
europepmc +1 more source
LES-CMC Simulations of turbulent hydrogen flame in a vitiated air CO-flow [PDF]
, 2011 Merci, Bart, Stankovic, Ivana
core
The Canadian Journal of Chemical Engineering, EarlyView.Abstract Synthetic jet fuel containing non‐petroleum‐derived kerosene can be produced from synthetic kerosene obtained through processes that include a hydroprocessing step. The potential use of non‐sulphided (reduced) nickel supported on alumina (Ni/Al2O3) was evaluated as an alternative to sulphided catalysts to saturate alkenes in sulphur‐free ...
Garima Chauhan +3 more
wiley +1 more source
Comparative Thermal and Fire Behavior of Rigid Polyurethane (PUR) and Polyisocyanurate (PIR) Foams Formulated with Recycled Poly(ethylene terephthalate) (PET) Polyols-Part 1. [PDF]
Materials (Basel)Skowron M +2 more
europepmc +1 more source
A study of Ni‐Co/CeO2 catalyst derived from metal–organic framework for dry reforming of methane
The Canadian Journal of Chemical Engineering, EarlyView.Abstract The efficacy of cobalt‐doped, MOF‐derived catalysts for dry reforming of methane (DRM) was examined. The focus was on the influence of varying nickel and cobalt molar ratios on catalytic performance. Three catalysts with Ni:Co ratios of 1:1, 1:0.5, and 0.5:1, were synthesized and tested with cerium oxide as a constant support. The DRM reaction
Ruth D. Alli, Nader Mahinpey
wiley +1 more source
Modelling of continuous low‐temperature emulsion co‐polymerization in 3D‐printed reactor
The Canadian Journal of Chemical Engineering, EarlyView.A kinetic model for the emulsion copolymerization of butyl acrylate/styrene at low temperatures is proposed and validated against experiments with a redox initiator system. The model was successfully transferred to a 3D‐printed tubular reactor and conversions of more than 80% and small particles sizes below 40 nm were observed.
Ferel Issa +2 more
wiley +1 more source
Multifunctional Phosphate Monomer Enabling LiNO<sub>3</sub> Solvation and In Situ Formation of Flame-Retardant Gel Polymer Electrolyte for High-Voltage Lithium Metal Batteries. [PDF]
Adv Sci (Weinh)Ma L +5 more
europepmc +1 more source
The Canadian Journal of Chemical Engineering, EarlyView.Abstract NOx emissions from gas boilers severely impact the environment, and flue gas recirculation (FGR) technology can effectively reduce such emissions, yet the effects of different FGR rates on combustion performance and NOx formation remain unclear. This study thus used numerical simulation (via ANSYS Fluent, adopting the realizable k‐ε turbulence
Chao Min +3 more
wiley +1 more source
The Canadian Journal of Chemical Engineering, EarlyView.Abstract The objective of this work is to demonstrate that the inclusion of an up‐flow anaerobic sludge bed (UASB reactor) within an industrial wastewater treatment plant reduces the plant's investment and operating costs compared to a system based solely on conventional complete‐mix activated sludge (CMAS), operating under the same design principles ...
Juan Manuel Morgan‐Sagastume +1 more
wiley +1 more source