Results 111 to 120 of about 33,938 (298)
Journal of Mechanical Engineering and Sciences, 2019 The present study deals with tapping of Al6061/SiC metal matrix composite. Stir casting technique was used for the fabrication of composite. Castings were produced by varying weight percentages of SiC (5%, 7.5% and 10%) of 23μm size in Al6061.
Nagaraja, Raviraja Adhikari, T. Yasir
doaj +1 more source
Generic Cutting Force Modeling with Comprehensively Considering Tool Edge Radius, Tool Flank Wear and Tool Runout in Micro-End Milling. [PDF]
Micromachines (Basel), 2022 Gao S, Duan X, Zhu K, Zhang Y.
europepmc +1 more source
A multi-sensor based online tool condition monitoring system for milling process [PDF]
, 2018 Tool condition monitoring has been considered as one of the key enabling technologies for manufacturing optimization. Due to the high cost and limited system openness, the relevant developed systems have not been widely adopted by industries, especially ...
Li, Weidong +4 more
core +1 more source
UCanWBGT: urban street canyon heat stress calculation for weather and climate models
Quarterly Journal of the Royal Meteorological Society, EarlyView.This work introduces UCanWBGT, a new model to calculate wet‐bulb globe temperature in an urban environment, suitable for use with weather and climate model data. We present the model, then verify its performance against observations made in the streets of Paris during heatwave conditions.
Jonathan K. P. Shonk +4 more
wiley +1 more source
Improved tool life in end milling Ti-6Al-4V through workpiece preheating [PDF]
, 2009 This paper presents the investigation of tool life improvement in end-milling of Titanium Alloy Ti-6Al-4V through workpiece preheating. End milling tests were conducted on Vertical Machining Centre with full immersion cutting.
A.K., M. Nurul Amin +4 more
core
Experimental study of coated carbide tools behaviour: application for Ti-5-5-5-3 turning [PDF]
, 2011 The goal of this paper is to study the relation between the input data (conditions and geometry of cut) and answers (wear of tool, forces and cutting temperatures) when machining the Ti-5-5-5-3 alloy treated. This study has shown that the cutting process
Baili, Maher +3 more
core +4 more sources
Smart Biomaterials and Dressings for the Treatment of Chronic Inflammatory Skin Diseases
Rare Metals, EarlyView.ABSTRACT Chronic inflammatory skin diseases, encompassing immune‐inflammatory conditions and infection‐associated dermatoses, pose significant clinical challenges due to high prevalence, recurrence, and therapeutic resistance, affect over 30% of the global population.
Zehao Lan +5 more
wiley +1 more source
Recent advances in fluorescent materials innovation and film‐based sensing application
Responsive Materials, EarlyView.This review systematically summarizes recent advances in high‐performance film‐based fluorescent sensors (FFSs), specifically covering the innovative strategies for engineering porous sensing films, and the sensitive and rapid detection for diverse target analytes. Current challenges for the further development of the sensors are discussed, guiding the
Xinyu Gou, Junxia Peng, Yu Fang
wiley +1 more source
Tool Wear Analysis due to Machining In Super Austenitic Stainless Steel
MATEC Web of Conferences, 2017 This paper presents tool wear study when a machinability test was applied using milling on Super Austenitic Stainless Steel AL6XN alloy. Eight milling trials were performed under two cutting speeds, 100 m/min and 150 m/min, combined with two feed rates ...
Polishetty Ashwin +2 more
doaj +1 more source
steel research international, EarlyView.Tool steels tested under injection molding conditions with glass‐fiber‐reinforced polymers, revealing how viscous dissipation drives hardness loss, even in PM grades. A sharp rise in wear with increasing injection volume rate and thermomechanical load uncovers striking material differences.
David Zidar +3 more
wiley +1 more source