Results 61 to 70 of about 219 (136)

Plasma formation during flash sintering of boron carbide – part I: plasma characteristics

In so-called Field Assisted Sintering Techniques such as Spark Plasma Sintering (SPS) or Flash Sintering (FS), ceramic powder compacts are densified at high sample temperature in the presence of an electrical field.
Bechteler, Christian, Gibson, Andrew, Falco, Simone, Todd, Richard I, Kirkpatrick, Andrew   +4 more
core   +1 more source

Electrical and Heat Distributions and Their Influence on the Mass Transfer during the Flash Spark Plasma Sintering of a Cu/Cr Nanocomposite: Experiments and Numerical Simulation. [PDF]

Materials (Basel), 2022
Abedi M, Asadi A, Sovizi S, Moskovskikh D, Ostrikov KK, Mukasyan A.   +5 more
europepmc   +1 more source

A short review of FS mechanisms

, 2019
The current views on flash sintering (FS) will be reviewed with focus on mechanism research [1]. The mechanism of FS has been under debate since its discovery and three main mechanisms were suggested: defect nucleation, Joule heating runaway and ...
Ze\u27ev Becker, Mattan, Tsur, Yoed
core  

Advances in Sintering Techniques for Calcium Phosphates Ceramics. [PDF]

Materials (Basel), 2021
Indurkar A, Choudhary R, Rubenis K, Locs J.   +3 more
europepmc   +1 more source

Mixed ionic electronic conductivity and flash sintering

, 2019
In this contribution, we present and discuss similarities and differences between two phenomena connected to creation and transport of point defects. One is flash sintering (FS) on which this conference is focused on and the other is switching in some ...
Riess, Ilan
core  

Comparison of Flash Sintering and Industrial Firing of Ceramic Wall Tiles: Microstructure and Properties

The ceramic tile industry is energy intensive, characterized by long firing times and high temperatures. Therefore, flash sintering (FS), which greatly conserves energy by completing sintering in a few seconds at low temperature, is of interest to this ...
Cetinkaya, Zeynep, Suvaci, Ender, Kose, Yeliz, Raj, Rishi, Yildiz, Betul   +4 more
core   +1 more source

Flash Sintering of YSZ/Al₂O₃ Composites: Effect of Processing and Testing Conditions. [PDF]

Materials (Basel), 2021
Biesuz M, Ometto A, Sglavo VM.
europepmc   +1 more source

Optimising a current-rate controlled flash sintering process for UO₂ pellet fabrication

Field assisted sintering techniques (FASTs) are currently being presented as an attractive alternative to the energy and time intensive fabrication routes employed for UO₂ and MOx nuclear fuel manufacture.
Green, C., Barron, N., Bostanchi, S., Ahmed, A., Abram, Timothy; id_orcid, Pearmain, D., Morgan, Jonathan, Goddard, D.T., Harrison, Robert; id_orcid   +8 more
core  

Light emission, electrochemical reduction and plasma formation during flash sintering of ceramics

Flash sintering of ceramics uses a combination of high electrical fields and elevated temperatures to achieve (Joule-)heating in the material leading to rapid densification of the material in less time and at significantly lower environmental ...
Bechteler, Christian
core   +1 more source

Investigation of the Effect of Different Sintering Methods on Mechanical Properties of Composite Materials Obtained From Cast Iron Waste

, 2023
Sinterleme günümüz teknolojisinde seramik, porselen ve ileri teknoloji seramik çalışmalarında oldukça çok kullanılan bir tekniktir. Son 15 yılda geleneksel sinterleme (GS) işlemi yerini daha farklı teknolojilere bırakmıştır.
Öztürk, Bengi̇nur
core