Results 71 to 80 of about 4,406 (240)
The improvement of dyeability of flax fibre by urea treatment [PDF]
, 2011 PurposeThe purpose of this paper is to improve the dyeability of flax fibre by modification via urea treatment and to explore the mechanism of such improvement.Design/methodology/approachThe modification to the flax fibre was carried out with different ...
C. Chen, X. Jiang, H. Sun, Y. Shen
core +1 more source
Process‐Induced Anisotropy and Fracture Behavior of Pellet‐3D Printed PLA and PLA/Flax Biocomposites
Polymer Composites, EarlyView.Fused Granular Fabrication of PLA and PLA/flax biocomposites, followed by tensile testing and fracture surface analysis to evaluate the effects of raster orientation and layer number on anisotropy and fracture behavior. ABSTRACT Fused granular fabrication (FGF) enables cost‐effective, large‐scale polymer additive manufacturing; however, the mechanical ...
Fernando Ancio +2 more
wiley +1 more source
Mechanical testing of natural fibre reinforced polyester resin composites and Mode 1 fracture toughness testing of resin blocks [PDF]
, 2008 Recent European Parliament directive requires companies to achieve materials recycling greater than 80% in particular in the automotive sector [1]. The research on natural fibre based composite materials fits well into this ecological image.
David-West, Opukuro S. +7 more
core
Composites Part C: Open AccessNatural fibre composites (NFCs) are not durable in the long run because of the susceptibility of natural fibres to environmental conditions and specifically moisture.
Subrata Chandra Das +3 more
doaj +1 more source
Comparative Analysis of Natural Fibre Reinforced Composite Material Using ANSYS
Advances in Materials Science and Engineering, 2021 The regulations of legislative bodies regarding the recycling and reusage of automotive materials has caused a great deal of obligation among automotive manufacturers to use natural fibres or green composites.
K. G. Saravanan +3 more
doaj +1 more source
Polymer Composites, EarlyView.Characterisation of glass fibre reinforced acrylic with acrylic‐tailored or multi‐compatible sizing agents. ABSTRACT Fiber‐reinforced infusible acrylic monomer resins are of interest as recyclable alternatives to epoxy and other thermoset resin composites, but the novelty of these resins causes published studies on acrylic‐matrix composites to often ...
Machar Devine +3 more
wiley +1 more source
Compressive strength of flax fibre bundles within the stem and comparison with unidirectional flax/epoxy composites [PDF]
, 2019 International audienceFlax (Linum usitatissimum L.) fibres are commonly used as reinforcement of composite materials. Nevertheless, literature shows that the compressive strength of flax-based composites is rather modest compared with materials ...
Pierre, Floran +5 more
core +1 more source
Photoperiod Influence on the Stem Structure of Fibre Flax
Agriculture, 2018 Plants of 13 fibre flax varieties were tested for their photosensitivity and differences of stems structure while grown in long and short daylight.
Pavlov Andrey +4 more
doaj +1 more source
NATURAL FIBRE COMPOSITES: A REVIEW ON FLAX FIBRES
Annals of the University of Oradea: Fascicle of Textiles, Leatherwork, 2017 In the composite industry, generally glass and carbon fibres are most widely used materials because of their high strength to weight ratio. On the other hand, in recent years, the use of natural fibres as reinforcement in composites have shown some esteem due to their properties such as light weight, low cost, recyclability, biodegradability and an ...
YUKSELOGLU S.Muge, CANOGLU Suat
openaire +1 more source
Polymer Composites, EarlyView.High‐Performance Sustainable Ski Core Bio‐Composite Derived from Bio‐Epoxy and Sisal Sibers Systems. ABSTRACT In pursuit of sustainable and high‐performance materials, this work investigates the potential of Algerian sisal fibers as renewable reinforcements in bio‐epoxy composites.
M. A. Kacem +4 more
wiley +1 more source