Results 161 to 170 of about 381,775 (307)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Biomechanical determinants of ground contact time and jump height during drop jumps in male athletes. [PDF]

PeerJ
Kubota H, Kishi K, Kurita T, Takai Y.
europepmc   +1 more source

Engineered Mycelial Scaffolds With Tunable Ultraviolet Protection, Wettability, Thermal Stability, and Spatial Mechanics

Advanced Engineering Materials, EarlyView.
Fungal mycelia grown into biodegradable scaffolds and infused with titania nanoparticles show enhanced ultraviolet shielding, thermal protection, and surface nonwettability. Properties were tuned by drying methods, revealing structure–function relationships.
Juwon S. Afolayan, Xin Zhang, Carole C. Perry   +2 more
wiley   +1 more source

Application of functional regression in biomechanical assessment of neck disability: Selection of clinically relevant variables. [PDF]

PLoS One
Aragón-Basanta E, Ayala G, Serra-Añó P, Page Á.   +3 more
europepmc   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Culturally Tailored Rehabilitation Approach "After zone III Flexor Tendon Tenolysis in the Index and Middle Fingers: A Case Report. [PDF]

J Hand Surg Glob Online
Awaad S, Sherifi O, Al Katheri S, Fallatah S, Alfuraydi A, Hamzah H.   +5 more
europepmc   +1 more source

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

Advanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour, Prithwish Tarafder, Anton Wiberg, Huanyu Li, Johan Moverare, Patrick Lambrix   +5 more
wiley   +1 more source

Imaging spectrum and diagnostic insights in Hirayama disease: A case series. [PDF]

Radiol Case Rep
Rajkumar I, Baskar A, Priyadarshee P, Murugan G, Rajasekhar KV.   +4 more
europepmc   +1 more source

Indo-European Verbal Flexion Was Analytical [PDF]

, 1913
University of Texas at Austin
core  

FLEXION REFLEX [PDF]

The Journal OF Nervous and Mental Disease, 1920
T. G. Brown, R. M. Stewart
openaire   +1 more source