Results 131 to 140 of about 758,737 (210)

Stresses in Above‐Ground Storage Tanks Subjected to Flood‐Borne Debris Impact

Safety Science and Technology, Volume 1, Issue 4, December 2026.
This study investigates the stresses induced in above‐ground storage tanks by flood‐borne debris, specifically steel pipes and wood poles. Findings demonstrate that debris impacts across the examined velocity range generate stresses within safe limits, not exceeding the yield stress threshold.
Sabarethinam Kameshwar, Md Manik Mia, Bobby Chen   +2 more
wiley   +1 more source

Correlation of Porosity and Permeability in Porous YSZ Microfiltration Membrane for Oil‐in‐Water Separation

International Journal of Applied Ceramic Technology, Volume 23, Issue 6, December 2026.
ABSTRACT Porous yttria‐stabilized zirconia (YSZ) symmetrical microfiltration (MF) membranes were fabricated via partial sintering of coarse YSZ (d50 = 2.7 µm) at 1300°C–1500°C. Fine YSZ (fine‐sized YSZ, d50 = 0.17 µm, 0–20 wt%) was employed as a sintering aid, and PMMA (0–10 wt%) served as a sacrificial template.
Muhammad Shoaib Anwar, Jang‐Hoon Ha, Jongman Lee, Hong Joo Lee, In‐Hyuck Song   +4 more
wiley   +1 more source

Optimizing Charpy Impact Strength of Material‐Extruded PLA Through Layer Height, Raster Angle, and Infill Geometry

Journal of Applied Polymer Science, Volume 143, Issue 44, November 20, 2026.
Charpy impact performance of material‐extruded PLA is governed by the coupled effects of layer height, raster angle, and infill geometry. Full‐factorial testing identifies layer height as the dominant factor and reveals a strong layer‐height–raster‐angle interaction.
Yazan Mashaki, Luis Hoi Fan, Shafahat Ali, Salman Pervaiz, Ibrahim Deiab   +4 more
wiley   +1 more source

Flexural strengthening of reinforced concrete beams using glass-fibre-reinforced-polymer laminates

, 2002
Structural rehabilitation and strengthening are becoming increasingly important in civil and structural engineering fields, as many structures are reaching their designed life while others experienced have to be strengthened due to various reasons.
Sun, Qin.
core  

From Agro‐Industrial Waste to Functional Packaging Using Antimicrobial and Mechanically Reinforced Starch Foams With Melon Seed and Rosemary

Journal of Applied Polymer Science, Volume 143, Issue 43, November 15, 2026.
Agro‐industrial waste was upcycled into biodegradable starch foams reinforced with melon seed and rosemary flours, yielding sustainable food packaging with enhanced mechanical performance, selective antimicrobial activity, and rapid biodegradation. ABSTRACT The demand for sustainable alternatives to petroleum‐based packaging has promoted starch‐based ...
Ana Carolina Agne Ferreira Zão, Naiara Jacinta Clerici, Flávio Fonseca Veras, Cecília Roratto Köhn, Adriano Brandelli, Juliane Elisa Welke, Patrícia Benelli, Alessandro de Oliveira Rios, Simone Hickmann Flôres   +8 more
wiley   +1 more source

The use of bolted side plates for flexural strengthened of reinforced concrete beams

, 2018
Reinforced concrete structures often need strengthening due to defective construction, having higher loads than those foreseen in the initial design of the structure, or as a result of material deterioration or accidental damage.
Su, KL, Li, LZ
core  

Combined Effects of Thermal Cycling Aging and Reinforcement Content on the Ball‐On‐Disk Wear of Additively Manufactured Polylactic Acid Composites

Polymer Composites, Volume 47, Issue 21, Page 19085-19107, 10 November 2026.
Thermal Aging and Tribological Tests of Additive Manufactured PLA Composites. ABSTRACT This study focuses on the additive manufacturing of pure polylactic acid (PLA) specimens and milled glass fiber (GF)‐filled PLA composites under thermal cycling aging and wear tests. Wear tracks have been analyzed via 3D optical profiling and SEM imaging.
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yilmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source

ACI design guide for flexural and shear strengthening of URM walls with FRP systems

, 2011
The American Concrete Institute (ACI) Committee 440 has recently published a design guide for strengthening of masonry with FRP systems. This paper summarizes and provides comments on the design protocols recommended by ACI 440 for flexural and shear ...
PROTA, ANDREA, Tumialan J. G., Galati N., Gold W. J.   +3 more
core  

Effect of Veil Interlayer Type and Placement on the Mechanical Response of Carbon and Glass Fiber/Epoxy Composites

Polymer Composites, Volume 47, Issue 21, Page 19261-19282, 10 November 2026.
Veil interlayers of five different chemistries (PI, FG, PPS, PEI, PEEK) were placed at two through‐thickness positions in carbon and glass fiber/epoxy laminates and evaluated under interlaminar shear (ILSS), three‐point bending (3PB) and axial buckling loading. The optimum placement was found to be loading mode dependent: near‐surface placement favored
Yavuz Selim Tarih, Burak Hülagü, Ömer Gündoğdu, Adem Yar   +3 more
wiley   +1 more source

Additive Manufacturing of Glass Fiber‐Reinforced Polypropylene and Its Behavior Under Controlled Hydrogen Exposure

Polymer Composites, Volume 47, Issue 21, Page 19563-19577, 10 November 2026.
Experimental and numerical assessment of GFRPP under lower experimental hydrogen pressures using tensile testing, SEM analysis, and hydrogen uptake estimation. ABSTRACT Glass fiber‐reinforced polypropylene (GFRPP) composites are increasingly explored for hydrogen transport and storage due to their lightweight nature and corrosion resistance.
Ahmadyar Qureshi, Ulises Martin, Abdul Mannan, Homero Castaneda   +3 more
wiley   +1 more source