Results 221 to 230 of about 7,237,339 (340)

Case Report: Unveiling segmental hemodynamic heterogeneity in internal jugular vein stenosis: a patient-specific CFD analysis. [PDF]

Front Cardiovasc Med
Li H, Dong J, Lu C, Xue X, Liu L, Zhang W, Zhou Y, Jiang H, Wu Y, Mao B, Zhu G, Ma H, Chen J, Hu Z, Zhou C, Ji X.   +15 more
europepmc   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Crystal Engineering of Reticular Materials for Gas- and Liquid-Phase Hydrocarbon Separation. [PDF]

Adv Mater
Li X, Mukherjee S, Zaworotko MJ.
europepmc   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Formulation and Characterization of Edible Bigel Inks for Structuring Fat Alternatives in 3D-Printed Foods. [PDF]

Gels
Zampouni K, Salamandrakis T, Biza T, Moschakis T, Katsanidis E.   +4 more
europepmc   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Thin-Film-Engineered Self-Assembly of 3D Coaxial Microfluidics with a Tunable Polyimide Membrane for Bioelectronic Power. [PDF]

Nanomicro Lett
Egunov AI, Tang H, Saenz PE, Karnaushenko DD, Luo Y, Zhong C, Wang X, Huang Y, Fedorov P, Merces L, Zhu M, Karnaushenko D, Schmidt OG.   +12 more
europepmc   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

The design of a low-cost 3D printed flow cell for synchrotron computed microtomography. [PDF]

J Synchrotron Radiat
Perera L, Garland P, Kirk C, Leonardi A, Love JB, Manchester T, Morrison CA, Rae R, Vance SSM, Ahmed SI.   +9 more
europepmc   +1 more source