Results 181 to 190 of about 108,291 (265)

Rheumatoid Arthritis and Coronary Artery Calcium Progression: A Case Cohort Analysis From ELSA‐Brasil

Arthritis Care &Research, EarlyView.
Objective To investigate the association between rheumatoid arthritis (RA) and coronary artery calcium (CAC) prevalence, incidence, and progression over four years in adults without prior cardiovascular disease. Methods A case‐cohort study within the Brazilian Longitudinal Study of Adult Health (ELSA‐Brasil) included 585 participants (86 patients with ...
Patrícia Fonseca Estrada, Marcos Rafael N. Cavalcante, Itamar de Souza Santos, Márcio S. Bittencourt, Vandrize Meneghini, Paulo A. Lotufo, Alessandra C. Goulart, Isabela M. Bensenor   +7 more
wiley   +1 more source

Adaptive Observer for Coupled Wave PDE and Infinite ODE With Sampled Data and Unknown Input: Application to Brain Hemodynamics Estimation

International Journal of Adaptive Control and Signal Processing, EarlyView.
This article proposes a convergent adaptive observer for a damped wave PDE and an infinite‐dimensional ODE coupled in cascade using sampled‐in‐space ODE state measurements. The proposed observer estimates the distributed states of the PDE and ODE along with unknown PDE parameters and spatial input.
Zehor Belkhatir, Sarah Mechhoud, Taous‐Meriem Laleg‐Kirati   +2 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

The impact of channel geometry and flow regime on endothelial orientation and morphology in vessel-on-chip

Jouybar M, van der Kallen S, Sahebali S, Bouten C, den Toonder JM.   +4 more
europepmc   +1 more source

From Clogging Mitigation to Clogging Acceleration: Particle Deposition Under Oscillatory Flow in Microfluidic Porous Media. [PDF]

Transp Porous Media
Okaybi W, Roman S, Soulaine C.
europepmc   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Characterization of Aluminized Layers on Inconel‐738 Alloy: Microstructure, Modeling of Aluminizing Kinetics, and Thermal Behavior

Advanced Engineering Materials, EarlyView.
This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe, Tuba Yener, Suayb Cagri Yener, Mourad Keddam, Cuma Bindal   +4 more
wiley   +1 more source

Real-Time Visualization of Turbulent Micromixing in a T-Mixer: Submillisecond Homogenization Revealed by Chemiluminescence. [PDF]

Anal Chem
Ishii Y, Ogawa T, Onda K, Miyagishi HV, Ashikari Y, Nagaki A, Asano S, Miyata K.   +7 more
europepmc   +1 more source