Results 151 to 160 of about 90,921,237 (241)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Lattice-Boltzmann for Porous Media: 100M⁺ GPU Hours. [PDF]

Sci Data
Armstrong RT, Tavakkoli O, Da Wang Y, Li Z, Mostaghimi P, Berg S, Ramstad T, Rücker M, McClure J.   +8 more
europepmc   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

A conditioning factor selection framework considering sample heterogeneity in debris flow susceptibility mapping. [PDF]

Sci Rep
Gao R, Wang A, Wu D.
europepmc   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Quenching for axisymmetric hypersurfaces under forced mean curvature flows

Here, we study the motion of axisymmetric hypersurfaces $\{\Gamma_t\}_{t\ge0}$ evolved by forced mean curvature flows in the periodic setting. We establish conditions that quenching occurs or does not occur in terms of the initial data and forcing term ...
Oka, Yusuke, Tran, Hung Vinh, Mitake, Hiroyoshi   +2 more
core  

Investigation of vorticity and secondary flow strength near the protected bridge pier in a sharp bend. [PDF]

Sci Rep
Moghanloo M, Vaghefi M.
europepmc   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

Computational investigation of MHD stagnation point flow of Eyring-Powell nanofluid with microorganisms over a cylinder under Cattaneo-Christov heat and mass flux. [PDF]

Discov Nano
Jayasri P, Durgaprasad P.
europepmc   +1 more source