Results 131 to 140 of about 254,781 (304)
PASTA‐ELN: Simplifying Research Data Management for Experimental Materials Science
Advanced Engineering Materials, EarlyView.Research data management faces ongoing hurdles as many ELNs remain complex and restrictive. PASTA‐ELN offers an open‐source, cross‐platform solution that prioritizes simplicity, offline access, and user control. Its in tuitive folder structure, modular Python add‐ons, and open formats enable seamless documentation, FAIR data practices, and easy ...
S. Brinckmann, G. Winkens, R. Schwaiger
wiley +1 more source
UNSTEADY FLOW THROUGH THE GAP OF SAVONIUS TURBINE ROTOR
TASK Quarterly, 2011 The paper presents a numerical analysis of unsteady flow through the gap of a Savonius turbine rotor, performed for varying integral turbine operating parameters calculated for the case under study as well as obtained from experiments described in the ...
JERZY ŚWIRYDCZUK +2 more
doaj
A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials
Advanced Engineering Materials, EarlyView.This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline +2 more
wiley +1 more source
TASK Quarterly, 2001 An experimentally tested air turbine stage and a real high-pressure (HP) steam turbine stage are calculated using the 3D RANS solver FlowER supplemented with the Baldwin-Lomax and Menter shear stress transport (SST) models. The computations of the model
PIOTR LAMPART +2 more
doaj
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Centrifugal pumps for rocket engines [PDF]
The use of centrifugal pumps for rocket engines is described in terms of general requirements of operational and planned systems. Hydrodynamic and mechanical design considerations and techniques and test procedures are summarized.
Campbell, W. E., Farquhar, J.
core +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Small, high-speed bearing technology for cryogenic turbo-pumps [PDF]
The design of 20-mm bore ball bearings is described for cryogenic turbo-machinery applications, operating up to speeds of 120,000 rpm. A special section is included on the design of hybrid bearings.
Eusepi, M. W. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source