Results 211 to 220 of about 1,023,937 (285)
Application of flux-cored wires at surfacing, remelting and in metallurgy
Avtomatičeskaâ svarka (Kiev), 2019 Yu.M. Kuskov
semanticscholar +3 more sources
2024 IEEE 74th Electronic Components and Technology Conference (ECTC)Heterogeneous integration (HI) and advanced packaging technology have been taken notice of semiconductor industry because it was believed as an alternative to overcome the slowing-down of Moore’s law, by splitting a chip into a few ones and then ...
Seok-Geun Ahn +4 more
semanticscholar +3 more sources
Some of the next articles are maybe not open access.
Related searches:
Related searches:
IEEE Transactions on Appiled Superconductivity, 1995
Cu artificial pinning centers (APCs) measuring 20 or 5 nm across were introduced to Nb/sub 3/Sn and Nb/sub 3/Sn(Ta) wire by means of powder metallurgy. The APCs increased the filament hardness by less than 10%. Stress anneals could be applied without affecting the Cu APC content or morphology.
C.L.H. Thieme, E. Rodrigues, S. Foner
openaire +3 more sources
Cu artificial pinning centers (APCs) measuring 20 or 5 nm across were introduced to Nb/sub 3/Sn and Nb/sub 3/Sn(Ta) wire by means of powder metallurgy. The APCs increased the filament hardness by less than 10%. Stress anneals could be applied without affecting the Cu APC content or morphology.
C.L.H. Thieme, E. Rodrigues, S. Foner
openaire +3 more sources
Development of Magnesium Alloys and Composite Through Flux and Fluxless Liquid Metallurgy Procedures
Journal of The Institution of Engineers (India): Series D, 2023Mayur Kumar Rajak +2 more
openaire +2 more sources
Improvement of production technology and improvement of quality characteristics of complex flux
Fundamental and applied problems of ferrous metallurgy, 2022The article considers the possibility of increasing the efficiency of the modern agglomeration process, which is carried out by improving the technology of complex flux production. The domestic and world experience of development and use in the processes
V. Bochka +3 more
semanticscholar +1 more source
Powder Iron Metallurgy Magnetic Materials Applied To Axial Flux Interior PM Brushless Motors
, 2005 BOJOI, IUSTIN RADU +3 more
openaire +2 more sources
, 2018
The accumulation of solid waste due to rapid industrialization has a negative impact on the environment. In this study, ZnS-containing waste from the mining-metallurgy industry was utilized for the synthesis of trigonal ZnIn2S4 layered crystals by a flux
M. Hojamberdiev +8 more
semanticscholar +1 more source
The accumulation of solid waste due to rapid industrialization has a negative impact on the environment. In this study, ZnS-containing waste from the mining-metallurgy industry was utilized for the synthesis of trigonal ZnIn2S4 layered crystals by a flux
M. Hojamberdiev +8 more
semanticscholar +1 more source
Physical Metallurgy Inspired Nano‐Features for Enhancement of Thermoelectric Conversion Efficiency
Advanced Theory and Simulations, 2018Thermoelectric (TE) materials are useful for the conversion of heat flux into electrical power and for heat removal and are, therefore, technologically important.
Y. Amouyal, Y. Gelbstein, D. Fuks
semanticscholar +1 more source
Methods for the Construction of Single-Sided Axial Flux Machines Using Soft Magnetic Composites
European Conference on Cognitive Ergonomics, 2018This paper presents an analysis of the different ways to construct a single-sided axial flux machine using soft magnetic composites (SMC). It focuses in particular on small machines that, in their simplest form, can be produced in a single pressing ...
J. Washington, S. Jordan, L. Sjöberg
semanticscholar +1 more source
Flux Effects in Metal Hydrogen Loading: Enhanced Mass Transfer
Journal of condensed matter nuclear science, 2015SRI has shown over hundreds of electrochemical experiments that the Fleischmann–Pons heat effect can be generated if high current, high loading and deuterium flux are present.
M. Mckubre, F. Tanzella
semanticscholar +1 more source