Results 41 to 50 of about 27,302 (254)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

(Figure 6b) Horizontal footprint diameter (90% of the total signal) and half-width (50%) of susceptibility, quadrature and in-phase conductivity

, 2012
(Figure 6b) Horizontal footprint diameter (90% of the total signal) and half-width (50%) of susceptibility, quadrature and in-phase ...
Bill SanFelipo (7974848), H Müller (7974845), Christian Hilgenfeldt (6965141), Müller, H, SanFelipo, Bill, Rubio, Belen, von Dobeneck, Tilo, Daniel Rey (7974851), Hilgenfeldt, Christian, Tilo von Dobeneck (6965342), Belen Rubio (2442997), Rey, Daniel   +11 more
core   +1 more source

Carbon footprint of oil products pipeline transportation

, 2021
As climate issues gradually attract public attention worldwide, the operation and construction of oil product pipelines have been attached with new energy-saving and emission-reduction targets.
Huang, L.,, Yan, Jinyue,, Liang, Y.,, Zhang, H.,, Liao, Q.,   +4 more
core   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Estimation of canopy structure and individual trees from laser scanning data [PDF]

, 2012
During the last fifteen years, laser scanning has emerged as a data source for forest inventory. Airborne laser scanning (ALS) provides 3D data, which may be used in an automated analysis chain to estimate vegetation properties for large areas ...
Lindberg, Eva
core  

Multimodal Data‐Driven Microstructure Characterization

Advanced Engineering Materials, EarlyView.
A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang, Santiago Benito, Özge Özgün, Sebastian Weber, Markus Stricker   +4 more
wiley   +1 more source

A comparison between cylindrical and cross-shaped magnetic vibration isolators: ideal and practical

Archives of Electrical Engineering, 2015
In this paper a cross-shaped isolator consisting of cuboidal magnets and a cylindrical isolator are compared by resonance frequency to volume ratio and shape. Both isolators are capable of obtaining a low resonance frequency, i.e. 0.15 Hz and 0.01 Hz for
Van Casteren D.T.E.H., Paulides J.J.H., Lomonova E.A.   +2 more
doaj   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Oxygen‐Tunnel Indium Tin Oxide Vertical Channel Transistors with Enhanced Current Density and Reliability for Monolithic 3D Compute‐In‐Memory Systems

Advanced Functional Materials, EarlyView.
Oxygen‐tunnel (OT) indium tin oxide (ITO) vertical channel transistors (VCTs) enable reliable, high‐density gain‐cell memory for monolithic 3D integration. A sandwiched SiN/SiO2/SiN OT stack selectively regulates oxygen transport, suppressing parasitic electrode oxidation while stabilizing channel oxygen vacancies, thereby suppressing carrier injection
Hyeonho Gu, Haksoon Jung, Yongwoo Lee, Hoichang Jeong, Yanfeng Zhao, Heesoo Yang, Minho Park, Hyeonjin Lee, Seunghun Baek, Minju Song, Junghwan Kim, Youngmin Jo, Hyunjin Park, Munhyeon Kim, Jae‐Joon Kim, Kyuho Jason Lee, Byungjo Kim, Jimin Kwon   +17 more
wiley   +1 more source