Results 91 to 100 of about 180,074 (262)

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

open access: yesAdvanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich   +3 more
wiley   +1 more source

Sensor fusion for estimating ground reaction force using insole-type foot pressure and inertial sensors

open access: yesMechanical Engineering Journal
Ground reaction force (GRF) analysis is critical to evaluate gait and running performances. However, installing force plates on the ground surface is costly, and their transportation is challenging owing to weight constraints and restricted measurement ...
Kiyoshi HIROSE   +4 more
doaj   +1 more source

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

open access: yesAdvanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik   +9 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

open access: yesAdvanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi   +3 more
wiley   +1 more source

Analytical rolling force model for hot rolling of wide-thick clad plates using a novel variable-trajectory cosine unified yield criterion

open access: yesMaterials Research Express
During the hot rolling of wide-thick clad plates, precise prediction of the rolling force is considered critical for ensuring interfacial bonding integrity, achieving uniform deformation, and optimizing process parameters.
Shun Hu Zhang   +4 more
doaj   +1 more source

The Agreement Between a Portable Contact-Mat and Force-Plates During Bilateral Vertical Jumps. [PDF]

open access: yesInt J Exerc Sci, 2022
Guppy SN   +6 more
europepmc   +1 more source

Forced vibrations of piezoelectric crystal plates [PDF]

open access: yesQuarterly of Applied Mathematics, 1962
Tiersten, H. F., Mindlin, R. D.
openaire   +2 more sources

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy