Results 191 to 200 of about 9,418,765 (294)

Fractional-order analysis and optimal control of the NERA model: stability, sensitivity, and numerical validation. [PDF]

Sci Rep
Pandey A, Ghosh S.
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Fractional-order differential model for knee implant recovery in smart health infrastructures. [PDF]

Sci Rep
Chinebu TI, Okafor KC, Nwadinigwe CU, Nwigwe JO, Chidiebere DR, Peace OI, Longe OM, Anoh K.   +7 more
europepmc   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Fractional order creep model of thawing sandstone incorporating nuclear magnetic resonance phase transition damage. [PDF]

Sci Rep
Fan K, Li F, Gao X, Bai Y.
europepmc   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Fractional-order modeling of vaccination strategies for measles transmission incorporating immune memory. [PDF]

Virus Res
Yunus AO, Olanrewaju OA.
europepmc   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Erratum: Battery SOH estimation based on thermodynamic parameters from an electrochemical fractional-order model and LSTM. [PDF]

iScience
Wang JV, Liu Y, Wang Q, Kang J, Meng P, Zhu G.   +5 more
europepmc   +1 more source

Discrepancies Between Micro Versus Macroscale Viscoelastic Properties in a Microplastic‐Tissue Composite Model

Advanced Engineering Materials, EarlyView.
This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser, Baptiste Le Roi, Omri Leshem, Joshua M. Grolman   +3 more
wiley   +1 more source