Results 121 to 130 of about 408,826 (276)

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Fractional colorings of cubic graphs with large girth [PDF]

, 2010
František Kardoš, Daniel Král͏̌, Jan Volec   +2 more
openalex   +1 more source

Circular Coloring and Fractional Coloring in Planar Graphs [PDF]

, 2020
Xiaolan Hu, Jiaao Li
openalex   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Fabrication of Multifunctional FeSi Gyroid Lattice Composites via Additive Manufacturing and Polymer Infiltration

Advanced Engineering Materials, EarlyView.
A two‐step approach combining laser powder bed fusion of FeSi electrical steel with Bakelite infiltration enables the fabrication of multifunctional gyroid lattice composites. The resulting structures exhibit high strength, magnetic anisotropy, and complete polymer infiltration, demonstrating a simple and scalable route toward lightweight, mechanically
Angelo F. Andreoli, Mayumi A. Nakahashi, Vitor E. Pinotti, Felipe O. C. Bernardo, Lidiane C. Costa, Francisco G. Coury, Ronei C. de Oliveira, Adilson J. A. de Oliveira, Carlos E. H. Ventura, Piter Gargarella   +9 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Removing Homocoupling Defects in Alkoxy/Alkyl‐PBTTT Enhances Polymer:Fullerene Co‐Crystal Formation and Stability

Advanced Functional Materials, EarlyView.
PBTTT‐OR‐R, a C14‐alkoxy/alkyl‐PBTTT polymer derivative, is of substantial interest for optoelectronics due to its specific fullerene intercalation behavior and enhanced charge‐transfer absorption. Comparing this polymer with (S) and without (O) homocoupling defects reveals that PBTTT‐OR‐R(O) forms stable co‐crystals with PC61BM, while PBTTT‐OR‐R(S ...
Zhen Liu, Jochen Vanderspikken, Paola Mantegazza, Stefania Moro, Mouna Hamid, Sigurd Mertens, Niko Van den Brande, Laurence Lutsen, Vincent Lemaur, David Beljonne, Giovanni Costantini, Koen Vandewal, Bruno Van Mele, Wouter Maes, Bart Goderis   +14 more
wiley   +1 more source

Intramolecular Down‐ and Up‐Conversion in Dimeric Tetracene Complexes Centered via Platinum(II) and Palladium(II)

Advanced Functional Materials, EarlyView.
Metal‐tetracene dimeric complexes are synthesized through the pyridyl coordination to either Pt(II) or Pd(II). Photophysical properties are systematically compared as a function of the metal using steady‐state and time‐resolved spectroscopy. The Pt(II) dimer exhibits efficient intramolecular singlet fission and subsequent intramolecular up‐conversion ...
Yifan Bo, Yuxuan Hou, Melchor Matabuena, Rik R. Tykwinski, Dirk M. Guldi   +4 more
wiley   +1 more source

Synchrotron Radiation for Quantum Technology

Advanced Functional Materials, EarlyView.
Materials and interfaces underpin quantum technologies, with synchrotron and FEL methods key to understanding and optimizing them. Advances span superconducting and semiconducting qubits, 2D materials, and topological systems, where strain, defects, and interfaces govern performance.
Oliver Rader, Sakura Pascarelli, Klaus Attenkofer, Anna A. Makarova, Karsten Holldack, Kai Rossnagel, Kristiaan Temst, George Kourousias, Stefano Carretta, Caterina Biscari, Helmut Dosch   +10 more
wiley   +1 more source

Fractional Skyrmion Tubes in Chiral‐Interfaced 3D Magnetic Nanowires

Advanced Functional Materials, EarlyView.
In chiral 3D helical magnetic nanowires, the coupling between the geometric and magnetic chirality provides a way to create topological spin states like vortex tubes. Here, it is demonstrated how the breaking of this coupling in interfaced 3D nanowires of opposite chirality leads to even more complex topological spin states, such as fractional ...
John Fullerton, Naëmi Leo, Jakub Jurczyk, Claire Donnelly, Dédalo Sanz‐Hernández, Luka Skoric, Nicholas Mille, Stefan Stanescu, Donald A MacLaren, Rachid Belkhou, Aurelio Hierro‐Rodriguez, Amalio Fernández‐Pacheco   +11 more
wiley   +1 more source