Results 121 to 130 of about 93,896 (272)

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Certain fractional integral inequalities using generalized Katugampola fractional integral operator

Malaya Journal of Matematik, 2020
Nale Asha B., Satish K. Panchal, L. Chinchane Vaijanath   +2 more
openaire   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

Advanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu, Timon Steinhoff, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Christian Klose, Ludger Overmeyer, Hans‐Jürgen Maier, Nina Merkert   +8 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

Some integral inequalities through tempered fractional integral operator

Communications Faculty Of Science University of Ankara Series A1Mathematics and Statistics
In this article, we adopt the tempered fractional integral operators to develop some novel Minkowski and Hermite-Hadamard type integral inequalities. Thus, we give several special cases of the integral inequalities for tempered fractional integrals obtained in the earlier works.
Erdal Gül, Abdüllatif Yalçın
openaire   +3 more sources

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source