Results 61 to 70 of about 10,603 (221)
Characterization and Tensile Fractography of Nano ZrO2 Reinforced Copper-Zinc Alloy Composites
Frattura ed Integrità Strutturale, 2019 Nano particulates fortified metal lattice composites are finding extensive variety of utilizations in car and sports hardware fabricating businesses. In the present investigation, an endeavor has been made to create copper-zinc-nano ZrO2 particulates ...
Madeva Nagaral +3 more
semanticscholar +1 more source
Microstructure, Defects, and Fatigue Response of High‐Strength Tool Steels
steel research international, EarlyView.The martensitic tool steel family is designed for use in various working environments where they are subjected to repeatedly high mechanical loads. Despite the continuous upgrade of material´s microstructures through compositional development or processing techniques, defects remain a critical factor for the tool performance by leading to fatigue ...
Katerina Chantziara +3 more
wiley +1 more source
Cyclic Strain Rate Dependent Low-Cycle Fatigue Behavior of Alloy 617
International Journal of Technology, 2023 Alloy 617 is identified as a potential material for defense applications, particularly in military air platforms. Therefore, this study aims to examine the impact of strain rate on Alloy 617 properties during low-cycle fatigue (LCF) at room ...
Rando Tungga Dewa +3 more
doaj +1 more source
Improving fatigue resistance of translucent 4Y‐PSZ zirconia through glass gradation
European Journal of Oral Sciences, EarlyView.Abstract To evaluate the effect of graded glass infiltration on the fatigue behavior and mechanical reliability of translucent 4Y‐PSZ zirconia before and after hydrothermal aging, disc‐shaped specimens were fabricated by uniaxial pressing and divided into control and glass‐graded groups (n = 36/group).
Felipe Machado Souza +12 more
wiley +1 more source
In Vitro Mechanical Tests for Modern Dental Ceramics
Frontiers in Dentistry, 2006 The fracture resistance of all-ceramic restorations is one of the major concerns in clinical applications of these materials. Before initiating a time-consuming and costly clinical investigation, an in vitro study can help to estimate the in vivo ...
L. Sadighpour +2 more
doaj
European Journal of Oral Sciences, EarlyView.Abstract This study evaluated (1) the load‐bearing capacity of molars restored with direct occlusal veneers fabricated either from short‐fiber‐reinforced composite (SFRC) or particulate‐filled composite (PFC) and the presence of internal voids within the materials, and (2) effect of water storage on the fracture load and correlation between internal ...
Topias Yli‐Urpo +6 more
wiley +1 more source
Indirect Tensile Test of Layered Marble and Analysis of Fracture Morphology and Mechanism
工程科学与技术, 2014 :With the aid of MTS815,large scale laser profilometer and SEM testing system,indirect tensile tests,fractography and meso fracture mechanism analysis were carried out on layered marbles taken from transportation tunnel of JinpinⅡ hydropower station ...
裴建良, 苏立, 刘建锋, 左建平
doaj
Biography of Are Tsirk (1937-2015): Flintknapper and scholar
Journal of Lithic Studies, 2015 Are Tsirk was as much a scholar as he was a flintknapper. These disciplines were intertwined and expressed in his experimental research, by way of his exploration of fractography, and his replication of stone tools which spanned the archaeological record
Steve Adams
doaj +1 more source
Breakage Characterization of Magnetite under Impact Loads and Cyclic Impact Loading
Energies, 2020 A series of impact compression tests were conducted to study the breakage characteristics of magnetite, as well as the impact pressure on its strain rate and dynamic compressive strength.
Liang Si, Yijun Cao, Guixia Fan
doaj +1 more source
Journal of Prosthodontics, EarlyView.Abstract Purpose In metal–ceramic restorations, the substructure fabrication method and design may affect the prognosis of the prosthesis. This study evaluated and compared the fracture resistance of metal–ceramic restorations fabricated with different substructure fabrication methods using two different alloy powders and designs.
Young‐Hoon Lee +4 more
wiley +1 more source