Results 41 to 50 of about 2,319 (181)

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Study of fractography of ferritic ductile iron at different temperatures and loading conditions

Materials Research Express
This study characterizes the fractography of ferritic ductile iron under various loads, including tensile, fatigue and bending, and impact conditions. The results indicate that ductile fracture is the primary mechanism observed during tensile testing at ...
Wenjie Wang, Zekun Wang, Zhiren Sun, Zhou Zhou, Kai Zhang, Li Ma, Yuwei Wang, Sen Yang, Zherong Huang, Kaikun Wang   +9 more
doaj   +1 more source

Failure Investigation of Alloy 625 Sockolets After Prolonged Service in an Ammonia Cracker Unit

Materials and Corrosion, EarlyView.
The failure of the sockolets was caused by intergranular cracking and fracture. The thick and highly brittle nitrided layer formed intergranular surface cracks, which propagated along grain boundaries into the base alloy substrate due to the presence of brittle Cr‐rich carbides. ABSTRACT Several sockolets of Alloy 625 operating at 540°C in contact with
Kamlesh Chandra, N. Naveen Kumar, Niraj Kumar   +2 more
wiley   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Microscopic observation of creep-fatigue crack propagation in lead-free solder

Nihon Kikai Gakkai ronbunshu, 2015
Creep-fatigue crack propagation tests of lead-free solder were conducted under various loading waveforms. The waveforms adapted in displacement-controlled tests were four triangular waveforms: pp waveform having fast loading-unloading, cc waveform having
Keisuke TANAKA, Ryosuke MIZUNO, Takashi FUJII, Takaharu SHIBUE, Kazunari FUJIYAMA   +4 more
doaj   +1 more source

Impact and Compressive Performance of 3D‐Printed PA6/Functionalized Graphene Nanoplatelet Sandwich Structures With Auxetic Cores

Polymer Composites, EarlyView.
Schematic of PA6/functionalized graphene nanoplatelet compounding and filament extrusion to 3D printing, sandwich panel fabrication, and mechanical characterization. ABSTRACT This study examines the impact and compressive behavior of additively manufactured polyamide 6 (PA6) nanocomposite sandwich panels reinforced with amine‐functionalized graphene ...
Russo Swart, Karim El‐Ghamrawy, Richard Johnston, Feras Korkees   +3 more
wiley   +1 more source

Fracturing behavior of brittle solids containing 3D internal crack of different depths under ultrasonic fracturing

International Journal of Mining Science and Technology, 2022
Ultrasonic fracturing (UF) can be used to form crack networks for oil or gas in the mining industry and hard rock excavation. In this paper, the three-dimensional internal laser-engraved crack method (3D-ILC) is introduced to make penny-shaped internal ...
Haijun Wang, Hanzhang Li, Lei Tang, Jianchun Li, Xuhua Ren   +4 more
doaj   +1 more source

Role of Fiber Sizing in Interfacial Relaxation, Water Uptake and Fatigue Properties of Acrylic‐Matrix Composites

Polymer Composites, EarlyView.
Characterisation of glass fibre reinforced acrylic with acrylic‐tailored or multi‐compatible sizing agents. ABSTRACT Fiber‐reinforced infusible acrylic monomer resins are of interest as recyclable alternatives to epoxy and other thermoset resin composites, but the novelty of these resins causes published studies on acrylic‐matrix composites to often ...
Machar Devine, Duncan Hornsby, Conchúr M. Ó Brádaigh, Dipa Ray   +3 more
wiley   +1 more source

Structural characterization and optimum machining parameters of jute/carbon fibre hybrid reinforced epoxy composite laminates

Polymer International, EarlyView.
Hybrid jute/carbon epoxy laminates have better mechanical performance and less drilling damage by the use of optimized stacking sequence and machining parameters. Abstract Three composite laminate systems were produced using the standard hand lay‐up method: jute‐fibre‐reinforced polymer (JFRP), carbon‐fibre‐reinforced polymer (CFRP) and a hybrid of the
Paulraj Prabhu, Anbalagan Arunkumar, Nadir Ayrilmis, Vellingiri Suresh, Ram Subbiah, Emarose Shankar   +5 more
wiley   +1 more source

Cyclic Strain Rate Dependent Low-Cycle Fatigue Behavior of Alloy 617

International Journal of Technology, 2023
Alloy 617 is identified as a potential material for defense applications, particularly in military air platforms. Therefore, this study aims to examine the impact of strain rate on Alloy 617 properties during low-cycle fatigue (LCF) at room ...
Rando Tungga Dewa, Aditia Aulia, Seon-Jin Kim, Raja Akbar   +3 more
doaj   +1 more source