Results 41 to 50 of about 2,320 (181)

Wood Sawdust as a Low‐Cost Filler in Whole‐Tire Reclaimed Rubber: Mechanical Characterization and Factory‐Scale Cost Analysis

Journal of Applied Polymer Science, EarlyView.
Whole‐tire reclaimed rubber is upgraded with wood sawdust, a carpentry by‐product available at no cost, across loadings from 0 to 20 wt%. At 5 wt%, tensile strength, elongation, hardness, viscosity, and water absorption all stay within commercial specification, and real factory data show an annual production saving near $62,000 with no capital ...
Mohammed S. Matar, Faris Tarlochan, Sami E. Alkhatib, Abdullah Abdelhamid   +3 more
wiley   +1 more source

Study of fractography of ferritic ductile iron at different temperatures and loading conditions

Materials Research Express
This study characterizes the fractography of ferritic ductile iron under various loads, including tensile, fatigue and bending, and impact conditions. The results indicate that ductile fracture is the primary mechanism observed during tensile testing at ...
Wenjie Wang, Zekun Wang, Zhiren Sun, Zhou Zhou, Kai Zhang, Li Ma, Yuwei Wang, Sen Yang, Zherong Huang, Kaikun Wang   +9 more
doaj   +1 more source

Damage detection in hot‐dip galvanized structural steel using AC potential drop method Schädigungsdetektion an feuerverzinktem Baustahl mittels Wechselstrom‐Widerstandsmessung

Materialwissenschaft und Werkstofftechnik, EarlyView.
This study demonstrates that the alternating current potential drop (ACPD) method detects early fatigue damage in hot‐dip galvanized structural steel. Analysis of the voltage gradient (du/dN) enables time‐resolved differentiation between coating and substrate cracks.
A. K. Kraemer
wiley   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Microscopic observation of creep-fatigue crack propagation in lead-free solder

Nihon Kikai Gakkai ronbunshu, 2015
Creep-fatigue crack propagation tests of lead-free solder were conducted under various loading waveforms. The waveforms adapted in displacement-controlled tests were four triangular waveforms: pp waveform having fast loading-unloading, cc waveform having
Keisuke TANAKA, Ryosuke MIZUNO, Takashi FUJII, Takaharu SHIBUE, Kazunari FUJIYAMA   +4 more
doaj   +1 more source

Impact and Compressive Performance of 3D‐Printed PA6/Functionalized Graphene Nanoplatelet Sandwich Structures With Auxetic Cores

Polymer Composites, EarlyView.
Schematic of PA6/functionalized graphene nanoplatelet compounding and filament extrusion to 3D printing, sandwich panel fabrication, and mechanical characterization. ABSTRACT This study examines the impact and compressive behavior of additively manufactured polyamide 6 (PA6) nanocomposite sandwich panels reinforced with amine‐functionalized graphene ...
Russo Swart, Karim El‐Ghamrawy, Richard Johnston, Feras Korkees   +3 more
wiley   +1 more source

Fracturing behavior of brittle solids containing 3D internal crack of different depths under ultrasonic fracturing

International Journal of Mining Science and Technology, 2022
Ultrasonic fracturing (UF) can be used to form crack networks for oil or gas in the mining industry and hard rock excavation. In this paper, the three-dimensional internal laser-engraved crack method (3D-ILC) is introduced to make penny-shaped internal ...
Haijun Wang, Hanzhang Li, Lei Tang, Jianchun Li, Xuhua Ren   +4 more
doaj   +1 more source

Role of Fiber Sizing in Interfacial Relaxation, Water Uptake and Fatigue Properties of Acrylic‐Matrix Composites

Polymer Composites, EarlyView.
Characterisation of glass fibre reinforced acrylic with acrylic‐tailored or multi‐compatible sizing agents. ABSTRACT Fiber‐reinforced infusible acrylic monomer resins are of interest as recyclable alternatives to epoxy and other thermoset resin composites, but the novelty of these resins causes published studies on acrylic‐matrix composites to often ...
Machar Devine, Duncan Hornsby, Conchúr M. Ó Brádaigh, Dipa Ray   +3 more
wiley   +1 more source

Microstructure, Defects, and Fatigue Response of High‐Strength Tool Steels

steel research international, EarlyView.
The martensitic tool steel family is designed for use in various working environments where they are subjected to repeatedly high mechanical loads. Despite the continuous upgrade of material´s microstructures through compositional development or processing techniques, defects remain a critical factor for the tool performance by leading to fatigue ...
Katerina Chantziara, Jens Bergström, Dimitrios Nikas, Mikael Thomas Grehk   +3 more
wiley   +1 more source

Improving fatigue resistance of translucent 4Y‐PSZ zirconia through glass gradation

European Journal of Oral Sciences, EarlyView.
Abstract To evaluate the effect of graded glass infiltration on the fatigue behavior and mechanical reliability of translucent 4Y‐PSZ zirconia before and after hydrothermal aging, disc‐shaped specimens were fabricated by uniaxial pressing and divided into control and glass‐graded groups (n = 36/group).
Felipe Machado Souza, Larissa M. M. Alves, Edisa O. Sousa, Tiago Moreira Bastos Campos, Giovana Assis Marcolino, Mariana Miranda de Toledo Piza, Rainã S. Dias, Satoshi Yamaguchi, Petra C. Gierthmuehlen, Lukasz Witek, Paulo G. Coelho, Estevam A. Bonfante, Ernesto B. Benalcazar‐Jalkh   +12 more
wiley   +1 more source