Results 141 to 150 of about 1,691,088 (393)

Additive Processing of Ti‐17 by Wire Arc Directed Energy Deposition: An Investigation of the Microstructure and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study focuses on processing the titanium alloy Ti‐17 using wire arc directed energy deposition (waDED), with an emphasis on the microstructure and mechanical properties. The waDED typical heat‐affected zone banding is characterized and related to the local mechanical properties.
Alexander Wenda, Thomas Klein, Florian Fahrnberger, Marcel Czipin, Karin Hartl, Clemens Simson, Martin Stockinger, Herbert Hutter   +7 more
wiley   +1 more source

Linear Elastic Fracture Mechanics Assessment of a Gas Turbine Vane. [PDF]

Materials (Basel), 2022
Orenes Moreno B, Bessone A, Solazzi S, Vanti F, Bagnera F, Riva A, Botto D.   +6 more
europepmc   +1 more source

The Structural Refinement of Commercial‐Purity Copper Processed by Equal Channel Angular Pressing with Low Strain Amplitude

Advanced Engineering Materials, EarlyView.
Equal channel angular pressing of commercial pure copper under low strain amplitude (≈0.48) induces concurrent continuous and localized discontinuous dynamic recrystallization, forming a duplex structure influenced by strain heterogeneity and recovery. Moderate hardening after 4–12 passes results from progressive high‐angle grain boundary formation via
Paula Cibely Alves Flausino, Nayara A. N. da Silva, Bárbara C. de Almeida, Taise M. Manhabosco, Elaine C. S. Corrêa, Maria T. P. Aguilar, Paulo R. Cetlin   +6 more
wiley   +1 more source

NANO-TESTS OF CONCRETE SAMPLES WITH AND WITHOUT NANO-TUBES

Наука и техника, 2013
The concrete samples originate from fracture mechanics tests performed on February 19, 2012, at the Department of Geo-Engineering and Building Materials of the Izhevsk State Technical University.After the fracture mechanics tests three types of small ...
B. M. Khroustalev, J. Eberhardsteiner, O. Lahayn, S. N. Leonovich, G. Yakovlev, G. Pervushin   +5 more
doaj  

Environmental Stress Cracking of High-Density Polyethylene Applying Linear Elastic Fracture Mechanics. [PDF]

Polymers (Basel), 2022
Thuy M, Pedragosa-Rincón M, Niebergall U, Oehler H, Alig I, Böhning M.   +5 more
europepmc   +1 more source

A nonlinear high temperature fracture mechanics basis for strainrange partitioning [PDF]

A direct link was established between Strainrange Partitioning (SRP) and high temperature fracture mechanics by deriving the general SRP inelastic strain range versus cyclic life relationships from high temperature, nonlinear, fracture mechanics ...
Halford, Gary R., Kitamura, Takayuki
core   +1 more source

Study made of mechanics of deformation and fracture of fibrous composites [PDF]

, 1967
Report summarizes the findings of studies made of the influence of both fiber and matrix characteristics upon the mechanics of deformation and fracture of fibrous composites.
Rosen, B. W.
core   +1 more source

Machine Learning‐Based Design of 3D‐Printable Microneedles for Enhanced Tissue Anchoring with Reduced Tissue Damage

Advanced Engineering Materials, EarlyView.
A machine learning‐driven framework is introduced to optimize 3D‐printable microneedles for enhanced tissue anchoring and reduced insertion damage. The optimized design achieves a 6.0‐fold improvement in pull‐out‐to‐penetration energy ratio over conventional shapes.
Jegyeong Ryu, Jiyeop Kim, Chan Wook Park, Hae‐Yoon Kim, Deukhee Lee, Amy Kyungwon Han   +5 more
wiley   +1 more source

Evaluation Strategies of Hil48 Yield Criterion in Application: Toward Sufficient and Necessary Conditions for Prediction of Plastic Anisotropy

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive analysis of the intrinsic relationships and applicability of Hill48 yield criterion. The applicability and error evaluation conditions for Hill48 are established based on specific experimental data. A parameter calibration strategy for N‐value based on error minimization is proposed, and the predictive accuracy is ...
Jinxin Wang, Zhenkai Mu, Longfei He, Wei Wang, Shuangjie Zhang, Yuzhong Liu, Huajun Yan, Xuerui Dai, Shibo Ma, Yong Hou   +9 more
wiley   +1 more source

Elastic property and fracture mechanics of lateral branch-branch junctions in cacti: A case study of Opuntia ficus-indica and Cylindropuntia bigelovii. [PDF]

Front Plant Sci, 2022
Mylo MD, Hoppe A, Pastewka L, Speck T, Speck O.   +4 more
europepmc   +1 more source