Results 71 to 80 of about 37,474 (260)

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

The Use of Percutaneous Screw Fixation without Fracture Site Preparation in the Treatment of 5th Metatarsal Base Non-Union

Foot & Ankle Orthopaedics, 2019
Category: Midfoot/Forefoot, Trauma Introduction/Purpose: Non-union following a proximal 5th metatarsal fracture can cause considerable pain with high morbidity with loss of work. Although many authors advocate early surgical management of zone 3 injuries
Gavin Heyes FRCS, MSc, Michael Grant MB BCH, Andrew P Molloy MBChB, MRCS (Ed), FRCS (Tr&Orth), Lyndon W Mason MRCS   +3 more
doaj   +1 more source

An Evaluation Index of Fracability for Reservoir Rocks Based on Fracture Process Zone. [PDF]

Materials (Basel), 2022
Chen H, Niu J, Zhai M.
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

A Numerical Method for Applying Cohesive Stress on Fracture Process Zone in Concrete Using Nonlinear Spring Element. [PDF]

Materials (Basel), 2022
Li Z.
europepmc   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

High Temperature Mechanical Properties of 280mm x 325mm Casting Bloom of Alloy Steel SAE8640

Teshugang, 2018
The mechanical properties of steel SAE8640 280mm x 325mm casting bloom (/% : 0.41C, 0.20Si, 0.80Mn, 0.005S, 0.014P, 0.46Cr, 0.43Ni, 0.21Mo, 0.043All, 0.0011O, 0.0054N) at 550~1200℃ has been measured by using Gleeble 1500 thermal simulation machine, and ...
王宁涛, 阮士朋, 段路昭, 王利军   +3 more
doaj  

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Experimental study on anisotropy characteristics of fracture toughness and fracture process zone in anthracite coal

Meitan xuebao
In order to determine the influence of anisotropy induced by primary bedding structure on fracture toughness and fracture process zone (FPZ) incubation characteristics of anthracite, the notched semi-circular bending (NSCB) anthracite samples with ...
Shuang GONG, Yixin ZHAO, Hansong ZHANG, Yongheng ZHOU, Canxin ZHAO, Wen WANG   +5 more
doaj   +1 more source