Results 41 to 50 of about 177,003 (269)
Metallurgical and Mechanical Examination of Fatigue-Induced Fracture in a Conveyor Drum Shaft [PDF]
Materials ResearchThis work investigates the fatigue failure mode of a shaft used in a conveyor system for mining applications through visual inspection, metallographic examination, fracture analysis, and mechanical testing. It was observed that a misalignment of about 5°
Anderson Luiz de Oliveira +10 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
STEREOLOGICAL ESTIMATES FOR ROUGHNESS AND TORTUOSITY IN CEMENTITIOUS COMPOSITES
Image Analysis and Stereology, 2011 Relatively weak interfaces between aggregate grains and the cementitious matrix initiate the damage evolution process leading to fracture. Coalescence between nearby interface cracks is promoted by the small nearest neighbour distances in a dense random ...
Piet Stroeven
doaj +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Applied Sciences, 2021 Asphalt mixture is a type of textured composite material made of aggregates and mastic part. Overall strength and failure behavior in such materials depends on the texture or heterogeneity of the mixture.
Jianxin He +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
MetalsA 2014Al matrix composite reinforced with 0.8 wt.% graphene nanoplatelets (GNPs) was prepared by pre-dispersion and ultrasonic melt casting. Subsequently, the as-cast 2014Al-GNP composite was subjected to hot extrusion under different parameters ...
Junjie Xiong +3 more
doaj +1 more source
Gazi Üniversitesi Fen Bilimleri Dergisi, 2020 In this study, the effect of annealing temperatures on the deformation aging of 0.4% C steels produced by Powder Metallurgy (PM) method was investigated. For this purpose, 0.4% by weight natural graphite powder and 0.3% by weight zinc stearate are added
Onur Altuntaş +2 more
doaj +1 more source
Metals, 2023 Bobbin tool friction stir welding (BTFSW) is a variant of the FSW process which uses the special two-shoulder tool that forms the top and bottom of a weld surface. As such, a significant simplification of the welding setup is achieved.
Sebastian Balos +9 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source