Results 81 to 90 of about 177,003 (269)
Dimension of Fracture Surfaces
Acta Polytechnica, 2007 The question of the universality of a dimension of fracture surfaces is discussed, and it is shown that such a general parameter may exist at least for a particular class of materials.
openaire +3 more sources
Metals, 2018 Tensile properties of the Fe⁻1.44C⁻8Mn⁻1.9Al (mass %) steel with a fully austenitic microstructure, obtained by rapid quenching from the austenite range, was determined at room temperature.
Guoqing Luan, Olena Volkova, Javad Mola
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Journal of Manufacturing and Materials ProcessingIn order to reduce the density and alloy cost of austenitic stainless steel, this study designed Fe-0.35C-12Cr-5Ni-(0,2,4)Al-(6,10)Mn (wt.%) stainless steels with different Al and Mn contents.
Nuoteng Xu +4 more
doaj +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Critical Parameters of the Athermal Electroplastic Effect in Metallic Materials
Инженерные технологии и системыIntroduction. Plastic deformation and electric current, acting separately, usually have opposite effects on the deformation behavior and flow stresses in electrically conductive materials.
Vladimir V. Stolyarov
doaj +1 more source
Advanced Engineering Materials, EarlyView.Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova +2 more
wiley +1 more source
Fracture Surface Evolution During Acidized Brine Injection in Calcareous Mudrocks. [PDF]
ACS Omega, 2023 Khan HJ, Al-Abdrabalnabi R, Al-Jawad MS.
europepmc +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Efficient Evaluation of Concrete Fracture Surface Roughness Using Fringe Projection Technology. [PDF]
Materials (Basel), 2023 Dai M, Wang X, Cheng C, Chen Z, Deng J.
europepmc +1 more source