Results 141 to 150 of about 614,598 (267)

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Current approaches to the diagnosis and treatment of postmenopausal osteoporosis

Терапевтический архив, 2009
Postmenopausal osteoporosis (OP) is a disease afflicting every three women above 50 years of age. The sociomedical significance of OP is determined by the development of fracture in minimal injuries resulting in disability and, occasionally, death.
Irina Aleksandrovna Baranova, I A Baranova   +1 more
doaj  

Management of hand fractures: Simple to complex

, 2017
Hand fractures are among the most common skeletal injuries. Approximately 150,000 hand fractures occur in the United States each year. The management of hand fractures consists of reduction, immobilization, and rehabilitation to return patients to their ...
Bernstein, Richard A, Bindra, Randy, Bednar, Michael S, Williams, Craig S   +3 more
core  

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

Advanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source

Microstructural, Mechanical, and Textural Evolution of Dissimilar Combination of Laser‐Welded Maraging Steel and 4340 Steel

Advanced Engineering Materials, EarlyView.
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl, Yu Dong, Alokesh Pramanik, Tapas Kumar Bandyopadhyay   +3 more
wiley   +1 more source

Influence of Fe Particle Size Distribution on Chemical Homogeneity, Microstructure, and Crack Formation in Fe–SiC Powder Blends Processed by PBF‐LB/M

Advanced Engineering Materials, EarlyView.
The influence of Fe particle size on in situ alloying of Fe–SiC powder blends in PBF‐LB/M is revealed. Contrary to expectations, the coarser Fe fraction provides a broader crack‐free processing window and slightly improved elemental homogeneity while producing higher but more variable hardness. The results highlight a complex trade‐off between particle
Anna Luise Strauch, Anastasiya Toenjes, Matthias Steinbacher   +2 more
wiley   +1 more source