Results 51 to 60 of about 839,378 (260)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Capillary fracture of soft gels

, 2013
A liquid droplet resting on a soft gel substrate can deform that substrate to the point of material failure, whereby fractures develop on the gel surface that propagate outwards from the contact-line in a starburst pattern. In this paper, we characterize
Bostwick, Joshua B., Daniels, Karen E.
core   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Osteochondral fragments in the metacarpo- and metatarsophalangeal joint and their clinical importance [PDF]

, 2011
The radiographic evaluation of the fetlock joint as part of a lameness or prepurchase examination often reveals osteochondral fragmentation. These fragments can either be causing lameness or have no clinical importance at the time of examination. However,
Declercq, Jeroen, Hauspie, Stijn, Martens, Ann, Saunders, Jimmy   +3 more
core   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Anisotropy in Fracking: A Percolation Model for Observed Microseismicity

, 2014
Hydraulic fracturing (fracking) using high pressures and a low viscosity fluid allow the extraction of large quantiles of oil and gas from very low permeability shale formations.
Norris, J. Quinn, Rundle, John B., Turcotte, Donald L.   +2 more
core   +1 more source

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source