Results 111 to 120 of about 165,045 (285)

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Distribution of Electrical Resistivity in Single Carbon Fiber Filaments and Its Correlation With Tensile Modulus

Advanced Engineering Materials, EarlyView.
A statistical framework is applied to quantify the distribution of electrical resistivity among individual filaments of two commercially available carbon fiber types. Correlations between filament resistivity, tensile modulus, and diameter are examined and complemented by TEM analysis to provide new insight into filament‐level variability relevant for ...
Nils Wieja, Daniel Sebastian Wolz, Philip Johannes Steinbild, Markus Löffler, Darius Pohl, Jan Wolf, Anja Winkler, Thomas Behnisch, Bernd Rellinghaus, Maik Gude   +9 more
wiley   +1 more source

COLLES'S FRACTURE AND CHAUFFEUR'S FRACTURE [PDF]

BMJ, 1938
R A, Fitzsimons, I C, Fracture
openaire   +2 more sources

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source