Results 151 to 160 of about 57,900 (317)
, 2016 We recall physical evidence coming from field data for intermittent fracture advancement and pressure fluctuations in case of hydraulic fracturing. We then simulate this behavior at mesoscopic level on a heterogeneous sample of saturated rock taking into
SECCHI, STEFANO +4 more
core
Advanced Engineering Materials, EarlyView.This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim +3 more
wiley +1 more source
Analysis on Erosion Wear Laws of High Pressure Manifold
Shiyou jixie, 2018 In view of the problem that the inner wall of the high-pressure manifold is damaged by erosion during the fracturing operation, the erosive wear rate and the erosion dispersion distribution of the inner wall of the high-pressure manifold are studied ...
Tu Yadong +5 more
doaj
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Continuous Sand Transport Unit for Fracturing in Shale Gas Development
Shiyou jixie, 2016 Given large displacement and high sand ratio in shale gas recovery,a large amount of sand and fast sanding at 3~8 m3/min are required.The sanding mode in conventional fracturing is inapplicable for its low transport efficiency and large area occupation ...
Wang Yunhai +4 more
doaj
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Effect of Cementing Quality on Casing Failure in Horizontal Section of Shale Gas Well
Shiyou jixie, 2019 The casing for shale gas well is subject to complicate forces. The inferior cementing quality will easily cause large stress concentration on the casing, which will lead to deformation failure.
Mai Yang +5 more
doaj
Advanced Engineering Materials, EarlyView.This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Electrified Damage in Motion Systems
Advanced Engineering Materials, EarlyView.The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir +2 more
wiley +1 more source