Results 21 to 30 of about 57,299 (306)

Experimental analysis and optimization of abrasive waterjet deep hole drilling process parameters for SS AISI 316L

Journal of Materials Research and Technology, 2023
Recent breakthroughs in component downsizing and miniaturization emphasise the requirement for deep-hole drilling with an increased aspect ratio, especially in the automobile sector for fuel injectors and the medical sector for manufacturing bone screws ...
Bharani Chandar J, N. Lenin, Siva Kumar, Naveen Kumar Gupta, Alagar Karthick, Rathina Suriyan, Hitesh Panchal, Abhinav Kumar, Anand Patel, Kishor Kumar Sadasivuni   +9 more
doaj   +1 more source

Model fusion using fuzzy aggregation: Special applications to metal properties [PDF]

, 2012
To improve the modelling performance, one should either propose a new modelling methodology or make the best of existing models. In this paper, the study is concentrated on the latter solution, where a structure-free modelling paradigm is proposed.
Bezdek, Chiu, Christophe Pinna, Deb, Dieter, Ee, Hansen, Haykin, Jang, John R. Yates, Kafkas, Mahdi Mahfouf, Mamdani, McClung, Montgomery, Qian Zhang, Rojas, Setnes, Sim, Sugeno, Sugeno, Takagi, Umbrello, Wang, Yen, Zadeh, Zadeh, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang, Zhang   +37 more
core   +1 more source

Process Control in Jet Electrochemical Machining of Stainless Steel through Inline Metrology of Current Density

Micromachines, 2019
Jet electrochemical machining (Jet-ECM) is a flexible method for machining complex microstructures in high-strength and hard-to-machine materials. Contrary to mechanical machining, in Jet-ECM there is no mechanical contact between tool and workpiece ...
Matin Yahyavi Zanjani, Matthias Hackert-Oschätzchen, André Martin, Gunnar Meichsner, Jan Edelmann, Andreas Schubert   +5 more
doaj   +1 more source

Design strategies for bi-metallic additive manufacturing in the context of wire and arc directed energy deposition

Materials & Design, 2022
While the recent research in manufacturing bi-metallic structures using wire and arc directed energy deposition focuses on feasibility studies to understand material compatibility, the study presented here encircles a larger design framework, integrating
Fereidoon Marefat, Joeri De Pauw, Angshuman Kapil, Nataliia Chernovol, Patrick Van Rymenant, Abhay Sharma   +5 more
doaj   +1 more source

The Effect of Tellurium on the Formation of MnTe-MnS Composite Inclusions in Non-Quenched and Tempered Steel

Metals, 2018
Te is a seldom-used alloying element, which is mainly used in free-machining steel. The Te content in this kind of steel is relatively low, and only a small amount of MnTe is generated. In previous studies, the effect of Te on the formation of inclusions
Ping Shen, Qiankun Yang, Dong Zhang, Shufeng Yang, Jianxun Fu   +4 more
doaj   +1 more source

Crystal Structure Investigation of Ferritic 73Fe24Cr2Si0.8Mn0.1Ni Steel for Multi-purpose Structural Material Applications

International Journal of Technology, 2018
Microstructural identification of synthesized steel with significant local content has been carried out. Alloy ingot was prepared using a casting technique. The samples were then formed into bulk steel by a machining process.
Parikin Parikin, M Dani, A.K. Jahja, R Iskandar, J Mayer   +4 more
doaj   +1 more source

Thick β-SiC CVD-Coated SiC Die System for Dry Cold Forging of Metals

Crystals, 2020
A thick β-SiC CVD (chemical vapor deposition)-coated SiC device was developed as a new punch and die system for dry, cold forging of pure titanium and austenitic stainless-steel works.
Tatsuhiko Aizawa, Tomoaki Yoshino, Ko-Ichi Ito, Tatsuya Fukuda   +3 more
doaj   +1 more source

Residual stress measurement round robin on an electron beam welded joint between austenitic stainless steel 316L(N) and ferritic steel P91 [PDF]

, 2017
This paper is a research output of DMW-Creep project which is part of a national UK programme through the RCUK Energy programme and India's Department of Atomic Energy.
A.K. Bhaduri, A.N. Forsey, ASTM, Bouchard, C.E. Truman, Chetal, D.J. Smith, Dai, EDF, Evans, F. Hosseinzadeh, Fitzpatrick, Fitzpatrick, H.C. Dey, Holden, Hosseinzadeh, Hosseinzadeh, ISO, ISO/TS 21432, J.A. Francis, Javadi, Javadi, Javadi, Javadi, Javadi, K. Abburi Venkata, Kartal, Kerr, Leggatt, M.C. Smith, Mahmoudi, Moat, N. Naveed, Naveed, Noyan, Olabi, Olabi, P.J. Bouchard, Pagliaro, Pagliaro, Prime, Prime, R.A. Ainsworth, Rossini, S. Gungor, S. Mahadevan, Schajer, Shan, Traore, Traore, Vasileiou, Vasileiou, Venkata, Venkata, VEQTER, Withers, Y. Javadi, Yaghi, Zhang   +57 more
core   +3 more sources

Dynamic Process Behavior in Laser Chemical Micro Machining of Metals

Journal of Manufacturing and Materials Processing, 2018
Laser chemical machining (LCM) is a non-conventional processing method that enables a smooth and precise micro structuring of metallic surfaces. However, a high-quality removal is limited to a laser power window of some 100 mW.
Salar Mehrafsun, Hamza Messaoudi
doaj   +1 more source

Analysis of Cutting Behavior during Tapping and Measurement of Tool Edge Temperature Measured by a Two-Color Pyrometer

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2013
This paper proposes a method for measuring the tool edge temperature during tapping. The infrared ray from the tool edge of the tapping tool was measured using a two-color pyrometer with an optical fiber.
Ryutaro TANAKA, Shuhei YAMAZAKI, Akira HOSOKAWA, Tatsuaki FURUMOTO, Takashi UEDA, Masato OKADA   +5 more
doaj   +1 more source