Results 41 to 50 of about 8,695 (230)
Heliyon, 2021 Although total hip arthroplasty (THA) is considered to be the most successful orthopedic operation in restoring mobility and relieving pain, common Metal-on-Metal (MoM) implants developed in the past decade suffer from severe inflammatory reactions of ...
Thomas S. Welles, Jeongmin Ahn
doaj +1 more source
Fatigue &Fracture of Engineering Materials &Structures, EarlyView.ABSTRACT The fatigue and fracture behavior of self‐piercing rivet (SPR) joints between AA6016 aluminum sheets (1–2 mm) and DX54D steel (0.95 mm) was studied under 90°, 45°, and 0° multiaxial loading. Pure shear (90°) loading produced the highest fatigue strength, whereas multiaxial (45°) loading resulted in reduced performance, with pure tension (0 ...
Alan Woo +5 more
wiley +1 more source
Modelling of Lubricated Electrical Contacts
Lubricants, 2022 Electrical contacts, although critically important for a wide range of applications, are susceptible to degradation due to fretting corrosion, especially when sliding and vibrations occur.
Robert L. Jackson, Santosh Angadi
doaj +1 more source
Nanoparticles in Periodontology and Implant Dentistry: From Mechanisms to Clinical Applications
Journal of Periodontal Research, EarlyView.Nanotechnology holds significant promise in improving dental care, yet there is a need for more reliable clinical studies to validate its effectiveness and safety. ABSTRACT Recent advances in nanotechnology are reshaping the landscape of periodontology and implant dentistry, particularly through the application of nanoparticles (NPs).
Chun Xu +4 more
wiley +1 more source
Metallosis and Corrosion Associated With Revision Total Knee Arthroplasties With Metaphyseal Sleeves
Arthroplasty Today, 2023 Metallosis and corrosion have been associated with metal-on-metal and modular total hip arthroplasty but are rarely described in the setting of primary or revision total knee arthroplasty (TKA).
Joshua P. Rainey, MD +5 more
doaj +1 more source
Heat Treated NiP–SiC Composite Coatings: Elaboration and Tribocorrosion Behaviour in NaCl Solution [PDF]
, 2009 Tribocorrosion behaviour of heat-treated NiP and NiP–SiC composite coatings was investigated in a 0.6 M NaCl solution. The tribocorrosion tests were performed in a linear sliding tribometer with an electrochemical cell interface.
A Hovestad +37 more
core +2 more sources
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2395-2410, June 2026.ABSTRACT This study investigates the impact of hydrogen soaking on the medium‐cycle fatigue behavior of various metallic materials commonly used in gas transmission pipelines. The tested materials include ex‐service gray cast iron, ex‐service X52 carbon steel, brass, and welded X52 carbon steel.
E. Kufoin +7 more
wiley +1 more source
MXene‐Enabled Wearable Biosensors: A Design Framework for Autonomous Biosensing
ChemElectroChem, Volume 13, Issue 9, 5 May 2026.Bridging nanoscale innovation with MXene to real‐time, patient‐centered health systems. MXenes, a rapidly expanding family of two‐dimensional transition metal carbides and nitrides, have emerged as leading materials for wearable bioelectronics due to their metallic conductivity, termination‐rich surfaces, mechanical compliance, and tunable interlayer ...
Jegan Rajendran, Gymama Slaughter
wiley +1 more source
THE DANG VAN FATIGUE CRITERION OF THE FRETTING PHENOMENON [PDF]
Analele Universităţii "Constantin Brâncuşi" din Târgu Jiu: Seria Inginerie, 2019 Fretting is now fully identified as a small amplitude oscillatory motion which induces a harmonic tangential force between two surfaces in contact. It is related to three main loadings, i.e. fretting-wear, fretting-fatigue and fretting corrosion.
Ștefan Ghimiși
doaj
Development of the Fretting Corrosion Test Equipment for the Automotive Electrical Connector [PDF]
한국정밀공학회지Fretting corrosion results from microscopic abrasion of connector contacts and is influenced by environmental conditions in automotive applications.
Jeong Hyun Kim, Sang Hoon Lee
doaj +1 more source