Results 121 to 130 of about 3,708,746 (293)

Development of polymeric and bioceramic tissue engineering scaffolds via fused deposition modeling

open access: yes, 2004
Study the feasibility of scaffold fabrication via Fused Deposition Modeling (FDM and using this rapid prototyping technique to overcome most, if not all, of the limitations faced in conventional scaffold fabrication methods.Master of Engineering ...
Ang, Ker Chin
core  

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

open access: yesAdvanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller   +3 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

open access: yesAdvanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt   +4 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Analisi della correlazione tra i parametri di processo e le prestazioni dei materiali polimerici ottenuti tramite fused deposition modeling [PDF]

open access: yes, 2015
Questa tesi si propone di realizzare una caratterizzazione del polimero ABS ottenuto con tecnica Fused Deposition Modeling in modo da ottenere dati utili alla realizzazione di parti strutturali tramite rapid ...
Leonelli, Mhervin
core  

Fused deposition modeling of PCL/HA/MMT biocompatible polymer nano-composites

open access: yes, 2016
This paper presents the development of a biocompatible polymer nano-composite material for the additive manufacturing (AM) process. The material was prepared by the mechanical of polycaprolactone (PCL), montmorillonite (MMT) and hydroxyapatite (HA) using
Abdul Haq, R. H.   +5 more
core   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

Production of functional equipment for food processor using Fused Deposition Modeling

open access: yes, 2012
This bachelor thesis deals with the production of component using the Fused Deposition Modeling method and economic comparison of this production to other manufacturing technologies.
Štancl, Václav
core  

Digital Light Processing of Thermoplastic Poly(methyl methacrylate) Photoresin Combined With Solvent Vapor Smoothing

open access: yesAdvanced Engineering Materials, EarlyView.
A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour   +5 more
wiley   +1 more source

Melt Electrowriting Combined with Fused Deposition Modeling Printing for the Fabrication of Three-Dimensional Biomimetic Scaffolds for Osteotendinous Junction Regeneration

open access: yesInternational Journal of Nanomedicine
Shengshan Ma,1,2,* Suyang Zheng,1,* Dong Li,3 Wenhao Hu,4 Liming Wang1 1Department of Orthopedic Surgery, Nanjing First Hospital, Nanjing Medical University, Nanjing, Jiangsu, People’s Republic of China; 2Department of Sports Medicine ...
Ma S, Zheng S, Li D, Hu W, Wang L
doaj  

Home - About - Disclaimer - Privacy