Results 131 to 140 of about 6,911 (192)

Enhancing the Performance of 3D‐Printed Polyamide Composites Through Pre‐ and Post‐Processing Methods

Polymer Composites, Volume 47, Issue 11, Page 10002-10017, 10 June 2026.
FDM‐printed polyamide composites and post‐processing by annealing. ABSTRACT In this study, composite filaments with a short carbon fiber (CF) reinforced polyamide 612 (PA612) were produced using the FDM method at three different raster angles (0°, ±45°, 90°).
Busra Eyri, Yusuf Yagci, N. Gamze Karsli, Taner Yilmaz   +3 more
wiley   +1 more source

Status of Polymer Fused Deposition Modeling (FDM)-Based Three-Dimensional Printing (3DP) in the Pharmaceutical Industry. [PDF]

Polymers (Basel)
Iqbal H, Fernandes Q, Idoudi S, Basineni R, Billa N.   +4 more
europepmc   +1 more source

Evaluation of Mechanical, Thermal, Rheological, and Biocompatibility Properties of Additively Manufactured Metal‐Reinforced Biocomposites Optimized by Reinforcement Ratios and Printing Parameters

Polymer Composites, Volume 47, Issue 11, Page 10258-10281, 10 June 2026.
Schematic illustration of PLA/316L stainless steel composite filament production via fused deposition modeling, demonstrating the trade‐off between stainless steel content, mechanical enhancement, and biocompatibility. ABSTRACT Polylactic acid (PLA) is a biodegradable thermoplastic widely used in biomedical devices; however, its inherent brittleness ...
İbrahim Baki Sahin, Bayram Sercan Bayram, Begum Pinarbasi, Pınar Yilgor, Berzah Yavuzyegit, İhsan Korkut   +5 more
wiley   +1 more source

Influence of Print Orientation on Surface Roughness in Fused Deposition Modeling (FDM) Processes. [PDF]

Materials (Basel), 2019
Buj-Corral I, Domínguez-Fernández A, Durán-Llucià R.   +2 more
europepmc   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Analysis of emission of volatile organic compounds and thermal degradation in investment casting using fused deposition modeling (FDM) and three-dimensional printing (3DP) made of various thermoplastic polymers. [PDF]

Environ Sci Pollut Res Int
Hejna A, Marć M, Szymański P, Mizera K, Barczewski M.   +4 more
europepmc   +1 more source

Development and validation of a 3D printed phantom for image quality assessment in fluoroscopy

Journal of Applied Clinical Medical Physics, Volume 27, Issue 6, June 2026.
Abstract Background Low‐contrast detectability is a key image‐quality parameter in fluoroscopy, directly influencing diagnostic accuracy and patient safety. Commercial phantoms such as the CDRAD provide reliable assessments but are costly and lack flexibility for routine use. Purpose To develop and validate a low‐cost 3D‐printed phantom for fluoroscopy
Túlio Guilherme Soares Marques, Diana Rodrigues de Pina   +1 more
wiley   +1 more source

3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries

Advanced Functional Materials, Volume 36, Issue 44, 1 June 2026.
Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling, Haoran Wang, Pan Yang, Rishav Agrawal, Alex R. Neale, Laurence J. Hardwick, Tom Hasell, Esther García‐Tuñón   +7 more
wiley   +1 more source

Impact of Processing Parameters on the Quality of Pharmaceutical Solid Dosage Forms Produced by Fused Deposition Modeling (FDM). [PDF]

Pharmaceutics, 2019
Alhijjaj M, Nasereddin J, Belton P, Qi S.   +3 more
europepmc   +1 more source

Dual‐Programmable Architected Magnetic Soft Materials: Tuning Mechano–Electric Responses by Inverse Design

Advanced Functional Materials, Volume 36, Issue 44, 1 June 2026.
ABSTRACT Materials that can deform, sense, and autonomously generate power in response to wireless magnetic fields, through both magnetic‐actuated shape transformation and charge generation, are an emerging focus in advanced functional materials research.
Zhi Zhao, Xiaojia Shelly Zhang
wiley   +1 more source