Results 171 to 180 of about 396,625 (338)

Fusion Power Plants

, 2005
Peter Stott, Garry McCracken
openaire   +2 more sources

Mitigation of Cracks in High‐Performance Nickel‐Based Superalloys in Powder Bed Fusion Laser Beam of Metals Using a Metal Matrix Composite Approach

Advanced Engineering Materials, EarlyView.
High‐performance nickel‐based superalloys are often not processible in additive manufacturing (AM) due to hot cracking. The findings in this manuscript propose an efficient method to mitigate cracking and enhance mechanical properties of these alloys by producing a metal matrix composite, contributing to the material and process perspective of the AM ...
Klaus Büßenschütt, Maël Pontoreau, Christian Haase, Johannes‐Henrich Schleifenbaum   +3 more
wiley   +1 more source

Activation of Perovskite Nanocrystals for Volumetric Displays Using Near-Infrared Photon Upconversion by Triplet Fusion. [PDF]

Molecules
Hu Y, Luo G, Niu P, Zhang L, Yu T, Chen J, Li Y, Zeng Y.   +7 more
europepmc   +1 more source

Impact of Hot Isostatic Pressing on Microstructure Evolution and Creep Performance of Powder Bed Fusion–Laser Beam Processed CM247LC

Advanced Engineering Materials, EarlyView.
The influence of Hot Isostatic Pressing (HIP) temperature on the microstructure and creep performance of powder bed fusion–laser beam processed CM247LC superalloy is investigated. Grain growth and γ’ precipitate evolution are characterized following HIP at varying temperatures.
Ahmed Fardan, Johannes Gårdstam, Eva Oscarsson, Håkan Brodin, Eduard Hryha   +4 more
wiley   +1 more source

Comparative Study of Experimental Methods for Measuring Thermal Properties of 100Cr6 Steel Powders

Advanced Engineering Materials, EarlyView.
This study investigates the thermal properties of 100Cr6 steel in both bulk and powder forms. Measuring the very low thermal conductivity typically exhibited by powders poses significant challenges. To address this, two novel measurement techniques—temperature gradient and finite laser pulse response—are introduced and evaluated by comparison with the ...
Junsheng Zhuo, Hagen P. Kohl, Dongmei Liu, Lisa Matthäus, Arne Bochmann, Aaron Berger, Sebastian Weber, Stefan Nolte, Stephanie Lippmann   +8 more
wiley   +1 more source

Environmental and technological implications of a theta-pinch fusion power plant

, 1974
T.A. Coultas, R.J. Burke, R.A. Krakowski
openalex   +2 more sources

Mechanical Properties of Different Austenitic High‐Nitrogen Steel Grades Produced by Powder Mixtures

Advanced Engineering Materials, EarlyView.
The effect of nitrogen content on the mechanical properties of austenitic stainless steels is investigated using tailored powder metallurgical processing. Different PM routes, including additive manufacturing, enable controlled nitrogen uptake and complex geometries.
Felix Radtke, Louis Becker, Lars Schultze‐Schlutius, Anke Kaletsch, Jonathan Lentz, Sebastian Weber, Christoph Broeckmann   +6 more
wiley   +1 more source

Implementation of a Low-Cost Navigation System Using Data Fusion of a Micro-Electro-Mechanical System Inertial Sensor and an Ultra Short Baseline on a Microcontroller. [PDF]

Sensors (Basel)
Winkler J, Badri-Hoeher S.
europepmc   +1 more source

Direct Natural and Artificial Aging of Aluminum Alloy AlSi10Mg After Laser Powder‐Bed Fusion

Advanced Engineering Materials, EarlyView.
Laser powder‐bed fusion of metals aluminum alloy AlSi10Mg has been directly aged. Artificial aging after natural aging is considered. The hardening potential is high for the top part of the samples as well as after short natural aging. The hardening potential is substantially reduced for the bottom part of the samples, as well as after natural aging of
Rabea Steuer, Benjamin Milkereit, Sigurd Wenner, Jette Broer, Florian Huber, Mirko Schaper, Olaf Kessler   +6 more
wiley   +1 more source

Vacuum pumping of tritium in fusion power reactors

, 1979
D.O. Coffin, C.R. Walthers
openalex   +1 more source