Results 61 to 70 of about 902,823 (249)

Effect of Gamma Irradiation on Botrytis cinerea Causing Gray Mold and Cut Chrysanthemum Flowers

Research in Plant Disease, 2015
Gray mold caused by Botrytis cinerea is one of the most important postharvest fungal pathogens of cut flowers. Here, gamma irradiation, an alternative for phytosanitary purposes, and sodium dichloroisocyanurate (NaDCC) were used to control B.
Eun-Hee Chu, Eun-Jung Shin, Hae-Jun Park, Rae-Dong Jeong   +3 more
doaj   +1 more source

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

The Effect of Gamma Irradiation as A Food Preservation Technology on The Shelf Life and Quality of Fresh-cut Watermelon

International Journal of Applied Sciences and Smart Technologies
Several methods for preserving food, particularly fresh fruit, aim to extend shelf life without compromising nutritional value. Food preservation technology utilizing irradiation techniques ensures food safety and stability by eliminating microbes and ...
Rieka Arkaninto Adeska, Nur Octaviany, Renaldy Bernardo Saragih, Retno Andrianti, Ridho Ridho, Harum Azizah Darojati, Dhita Ariyanti   +6 more
doaj   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

Advanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang, Jianxiang Zhao, Zhaoqi Chen, Hao Gong, Yinsen Yan, Junlei Tao, Yong Yang   +6 more
wiley   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Crystal structure changes and weight kinetics of silicon-hexaboride under gamma irradiation dose

Results in Physics, 2018
The silicide hexaboride (B6Si) was irradiated with 60Co at room temperature to study the structural changes and weight kinetics. The B6Si samples were irradiated using a gamma source with a dose rate (D) of 0.27 Gy/s.
M.N. Mirzayev, S.H. Jabarov, E.B. Asgerov, R.N. Mehdiyeva, T.T. Thabethe, S. Biira, N.V. Tiep   +6 more
doaj   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

Advanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner, Anna Sophie Jelinek, Velislava Terziyska, Peter Wagatha, Wolfram Knabl, Christian Mitterer, Helmut Clemens, David Holec   +7 more
wiley   +1 more source

High‐Entropy Alloy Interlayers Toward Advanced Joining for High‐Performance Structural Applications: Current Progress and Emerging Challenges

Advanced Engineering Materials, EarlyView.
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan, Jiafen Song, Jinglong Li, Jiangtao Xiong, Tao Yang   +4 more
wiley   +1 more source