Results 51 to 60 of about 1,153,137 (275)

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Recovery and reanalysis of archived airborne gamma spectrometry data from the 1991 Dounreay survey [PDF]

, 2012
Archived Airborne Gamma Spectrometry (AGS) data from the 1991 NIREX characterisations of Caithness have been recovered. The separate gamma spectrometry and positional data streams for approximately 120000 measurements have been combined into a single ...
Cresswell, A., A.J. Cresswell
core   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Comparative analysis of gamma dose rates measured by ion chamber in and around the historical sacral objects in Bosnia and Herzegovina [PDF]

Nuclear Technology and Radiation Protection, 2019
The main objective of this study was to investigate the correlation between the indoor and outdoor ambient dose equivalent rates measured by the ion chamber inside and around the historical sacral objects at a few locations in Bosnia and Herzegovina. The
Avdić Senada, Beganović Adnan, Lagumdžija Armin, Sadiković Samra, Pehlivanović Bećo, Demirović Damir, Kadić Irma   +6 more
doaj   +1 more source

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

Y-Spect: A Multi-Method Gamma Spectrometry Analysis Program

Atom Indonesia, 2013
To accomplish a more accurate, precise and correct interpretation and analysis of spectrum data collecting from a gamma spectrometry counting system, a fully interactive computer code, named Y-Spect, has been developed by using the Delphi 7.0 programming
P.I. Yazid
doaj  

Symmetry‐Guided Multifunctional Acoustic System Based on Mechanically Actuated Sonic Crystals

Advanced Engineering Materials, EarlyView.
This study presents the design, simulation, and experimental validation of amultifunctional acoustic metamaterial based on rotationally engineered sonic crystals.By tuning cylinder orientations, controllable band gaps and six distinct functionalities—including switching, topological insulation, beam splitting, and logic operations—areachieved ...
Yuanyan Zhao, Sriram Subramanian, Gianluca Memoli   +2 more
wiley   +1 more source

Automated preparation of water samples for low-level gamma spectrometry

Acta Chimica Slovenica, 2016
The analysis of water samples using gamma spectrometry requires the preconcentration of the sample in order to determine the content of low-level radionuclides. An automated evaporator was used for this purpose during the preparation of approximately 250
Marijan Nečemer, Marko Gerbec
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source