Results 151 to 160 of about 9,452 (298)
Atomization process for metal powder
, 2004 A new atomization process has been developed, which combines pressure and gas atomization. The melt leaves the pressure nozzle as a hollow thin film cone. After the pre-filming step, the melt is atomized by a gas stream delivered by a ring nozzle.
Uhlenwinkel, V +4 more
core +1 more source
In Situ Amine Formation to Modulate MOF‐Derived PdIn N‐Doped Carbon Catalysts
Advanced Materials, EarlyView.An amine‐assisted approach converts PdIn‐MOF into PdIn intermetallic nanoparticles embedded in N‐doped carbon. In situ‐generated amines trigger early Pd nucleation, producing smaller PdIn domains than direct pyrolysis. Amine sterics and basicity tune composition and particle size, while solvent and amine co‐determine textural features.
Gonzalo Egea +9 more
wiley +1 more source
Polymorph‐Specific Electronic Transduction in WO3 during Molecular Sensing
Advanced Materials, EarlyView.Metal‐oxide polymorphs with similar surface chemistry can nevertheless exhibit distinct sensing properties. In γ‐ and ε‐WO3, analyte adsorption appears comparable; yet, only ε‐WO3 induces a pronounced lattice electronic perturbation that accommodates charge in sub‐conduction band minimum states.
Matteo D'Andria +6 more
wiley +1 more source
Advanced Materials, EarlyView.This review highlights the role of self‐assembled monolayers (SAMs) in perovskite solar cells, covering molecular engineering, multifunctional interface regulation, machine learning (ML) accelerated discovery, advanced device architectures, and pathways toward scalable fabrication and commercialization for high‐efficiency and stable single‐junction and
Asmat Ullah, Ying Luo, Stefaan De Wolf
wiley +1 more source
Modelling Gas Flow Behaviour in Gas Atomizer
, 2022 Gas atomization is regarded as a reliable method for creating high-quality metal powders from molten metal. The liquid metal is fed into the chamber as a free-falling stream through a nozzle, where it is impinged by high-velocity gas jets, causing degeneration and production of metal droplets, which solidify to create metal powders.
openaire +1 more source
Transparent Perovskite Light‐Emitting Diodes with Conductive Oxide Top Electrodes
Advanced Materials, EarlyView.Transparent perovskite light‐emitting diodes (TrPeLEDs) enable simultaneous display and transparency, expanding application possibilities. Using a metal oxide buffer layer and pulsed laser deposition, TrPeLEDs with diverse compositions and architectures are demonstrated.
Michele Forzatti +11 more
wiley +1 more source
Advanced Materials, EarlyView.The field of polymer thermoelectrics is entering a new era, featuring breakthroughs in addressing the conventional performance disparity between p‐type and n‐type polymers, pioneering doping frontiers, and sophisticated decoupling strategies. This review explores innovations in molecular design and superior stabilities, bridging the gap from ...
Suhao Wang
wiley +1 more source
Cooling Rate Calculation of Non-Equilibrium Aluminum Alloy Powders Prepared by Gas Atomization
, 2009 The cooling rate of aluminum alloy powders prepared by ultrasonic gas atomization process was calculated through the convection heat transfer principle.
He, S. W., Guo, Sheng,, Liu, Y.
core +1 more source
Size-Dependent Phase Transformation during Gas Atomization Process of Cu⁻Sn Alloy Powders. [PDF]
Materials (Basel), 2019 Pan H, Ji H, Liang M, Zhou J, Li M.
europepmc +1 more source
Advanced Materials, EarlyView.Elephant‐skin‐inspired crack networks are programmed in porous diatomaceous earth (DE)‐cement composites using substrate‐guided, stress‐concentration induced fracture. The resulting crack lattices act as capillary conduits that redistribute water, while the porous matrix stores moisture.
Qingya Huang +5 more
wiley +1 more source