Results 161 to 170 of about 143,065 (295)

Experimental investigation of factors affecting microbial liquefaction mitigation in coastal liquefied sand. [PDF]

Front Microbiol
Hu J, Liu M, Ren J, Li Y, Yuan H.
europepmc   +1 more source

Isotope Separation by Con-current Gas Centrifuge, (I)

Journal of the Atomic Energy Society of Japan / Atomic Energy Society of Japan, 1964
Akira KANAGAWA, Yoichi TAKASHIMA
openaire   +2 more sources

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Direct Pulp Capping of Dental Pulp with Two Different Autologous Platelet Concentrates A-PRF+ and H-PRF-A Report on Two Cases. [PDF]

Dent J (Basel)
Kirilova J, Yovchev D.
europepmc   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Polysaccharide-modified quinoa-wheat composite flour: Optimization of functional properties and flavor profiles in steamed buns. [PDF]

Food Chem X
Fan H, Qiao W, Zhu D, Yang L, Jiang S, Liu H.   +5 more
europepmc   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Protocol for obtaining polyhydroxyalkanoates from microbial cultures: Production, quantification, and analytical assays. [PDF]

STAR Protoc
Manoli MT, Hernández-Herreros N, Rivero-Buceta V, Rodríguez A, Prieto MA.   +4 more
europepmc   +1 more source

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

PFAS Removal During Pyrolysis of Biosolids Is Affected by Initial PFAS Concentration and Pyrolysis Efficiency. [PDF]

Water Environ Res
McNamara PJ, Calteux J, Redman E, Adkins C, McKnight T, Moss L, Ayala R, Ishida S, Liu Z.   +8 more
europepmc   +1 more source