Results 61 to 70 of about 2,984,753 (355)

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Method of aerodynamic improvement of axial and centrifugal compressor stages of gas turbine engines

Авіаційно-космічна техніка та технологія
The development of approaches to aerodynamic improvement of compressor stages of gas turbine engines based on numerical modeling of three-dimensional turbulent gas flows remains a pressing task, which is of great importance for the design and ...
Natalya Zinevich
doaj   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Fabrication of Multifunctional FeSi Gyroid Lattice Composites via Additive Manufacturing and Polymer Infiltration

Advanced Engineering Materials, EarlyView.
A two‐step approach combining laser powder bed fusion of FeSi electrical steel with Bakelite infiltration enables the fabrication of multifunctional gyroid lattice composites. The resulting structures exhibit high strength, magnetic anisotropy, and complete polymer infiltration, demonstrating a simple and scalable route toward lightweight, mechanically
Angelo F. Andreoli, Mayumi A. Nakahashi, Vitor E. Pinotti, Felipe O. C. Bernardo, Lidiane C. Costa, Francisco G. Coury, Ronei C. de Oliveira, Adilson J. A. de Oliveira, Carlos E. H. Ventura, Piter Gargarella   +9 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

Performance simulation of multi-stage axial-flow compressor of turbo-shaft engine with account for erosive wear nonlinearity of its blades

Научный вестник МГТУ ГА, 2020
The construction and useful practice of gas-turbine engine diagnosis systems depend largely on the availability of the engine mathematical models and its certain components in their structure.
V. A. Potapov, A. A. Sanko
doaj   +1 more source

Unique Performance Considerations for Printable Organic Semiconductor and Perovskite Radiation Detectors: Toward Consensus on Best Practice Evaluation

Advanced Functional Materials, EarlyView.
A lack of standard approaches for testing and reporting the performance of metal halide perovskites and organic semiconductor radiation detectors has resulted in inconsistent interpretation of performance parameters, impeding progress in the field. This Perspective recommends key metrics and experimental details, which are suggested for reporting in ...
Jessie A. Posar, Matthew Large, Andrea Ciavatti, Laura Basiricò, Beatrice Fraboni, Paul J. Sellin, Attila J. Mozer, Marco Petasecca, Matthew J. Griffith   +8 more
wiley   +1 more source

Research on aerodynamic performance of centrifugal compressors for hydrogen-mixed natural gas.

PLoS ONE
Natural gas-doped hydrogen transportation has been widely used in industrial engineering. The change of the physical parameters of the conveying medium affects the working performance of the centrifugal compressor.
Jingya Dong, Bin Song, Xiaoyun Yuan, Wanchun Jin, Jin Wang   +4 more
doaj   +1 more source