Results 211 to 220 of about 7,017,602 (384)

Non-Singleton Type-3 Fuzzy Approach for Flowmeter Fault Detection: Experimental Study in a Gas Industry. [PDF]

Sensors (Basel), 2021
Wang JH, Tavoosi J, Mohammadzadeh A, Mobayen S, Asad JH, Assawinchaichote W, Vu MT, Skruch P.   +7 more
europepmc   +1 more source

Oil and Gas Industry Financing

, 1969
Caroline Rae
openalex   +2 more sources

Evaluating Dielectric Properties for Semicrystalline Thermoplastics to Analyze the Thermal and Rheological Properties in Laser‐Based Powder Bed Fusion of Plastics

Advanced Engineering Materials, EarlyView.
This study aims to establish a link between the dielectric properties of polyamide 12 (PA12) and its thermal and rheological properties using dielectric analysis (DEA). A standardized methodology is introduced to determine melting and crystallization temperatures.
Benedikt Burchard, Joseph Hofmann, Katrin Wudy   +2 more
wiley   +1 more source

Coal seam gas industry methane emissions in the Surat Basin, Australia: comparing airborne measurements with inventories. [PDF]

Philos Trans A Math Phys Eng Sci, 2021
Neininger BG, Kelly BFJ, Hacker JM, Lu X, Schwietzke S.   +4 more
europepmc   +1 more source

Natural gas profile: the baking industry

, 1975
Not Given Author
openalex   +2 more sources

Powder Metallurgy Preparation of Metastable β Ti–Cr–Ge Alloys for Medical Applications

Advanced Engineering Materials, EarlyView.
This study develops metastable β Ti–Cr–Ge alloys using powder metallurgy for biomedical implants. The Ti–10Cr–2Ge alloy exhibits superior mechanical performance with high yield strength (>1100 MPa), low Young's modulus (<85 GPa), and excellent strain hardening behavior.
Teddy Sjafrizal, Damon Kent, Ali Dehghan‐Manshadi, Matthew S. Dargusch   +3 more
wiley   +1 more source

Energy Resources and Low-temperature Gas Industry

, 1977
Masaki Watanabe
openalex   +2 more sources

Optimized Strategy for Fabricating High‐Aspect‐Ratio Periodic Structures Over Large Areas Using ps‐Direct Laser Interference Patterning

Advanced Engineering Materials, EarlyView.
Picosecond direct laser interference patterning (DLIP) enables precise microstructure fabrication on stainless steel. Using a multiscan approach, high‐aspect‐ratio patterns are achieved. Fluence influences structure growth and homogeneity, with smaller periods yielding better uniformity.
Fabian Ränke, Marcelo Sallese, Marcos Soldera, Ignacio Tabares, Flavio Soldera, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Design, simulation, and manufacturing of analyzer optical cell for detection and measurement of injectable odorant at pressure reduction stations

Heliyon
The absence of a mercaptan compounds analyzer in natural gas pressure reduction stations (PRS) odorizer leads to inaccuracies in the injection dosage, often resulting in quantities beyond standard limits and consequently increasing odorant consumption ...
Hamideh Samari Jahromi, Mohsen Abdollahi, Azardokht Mazaheri, Soleyman Mantaghi, Amirhomayoon Rezaeian, Ali Sadouni, Hamidreza Naseri, Kioumars Taheri, Fariborz Hashemipour, Foad Hamzavi, Abdolsamad Naseh   +10 more
doaj  

Sol–Gel Synthesis of Ca2.5Ag0.3Sm0.2Co4O9 Semiconducting Materials for Thermoelectric Applications in Aerospace Systems

Advanced Engineering Materials, EarlyView.
Ca2.5Ag0.3Sm0.2Co4O9 semiconductor materials are synthesized and produced in this study using the sol–gel and cold pressing techniques for thermoelectric generator applications. As template samples are added, the Seebeck coefficient and power factor values rise, peaking at 800 °C for Ca2.5Ag0.3Sm0.2Co4O9 at 274.47 μV K−1 and 0.58 mW mK−2, respectively.
Enes Kilinc, Fatih Uysal, Mucahit Abdullah Sari, Huseyin Kurt, Erdal Celik   +4 more
wiley   +1 more source