Results 71 to 80 of about 178,074 (266)

Determination of the fracture closure pressure in fractural-cavity carbonate reservoirs using a failure criterion based on asperity behavior

open access: yesFrontiers in Earth Science
As fluid flow paths in fractural-cavity carbonate reservoirs, fractures have a significant impact on the production performance of carbonate reservoirs.
Yuanyuan Tian   +6 more
doaj   +1 more source

Technical efficiency of the urban gas industry in china. [PDF]

open access: yesEnviron Sci Pollut Res Int, 2023
Li F, Wu X, Phillips MA.
europepmc   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal   +4 more
wiley   +1 more source

Catalytic and Noncatalytic Conversion of Methane to Olefins and Synthesis Gas in an AC Parallel Plate Discharge Reactor

open access: yesJournal of Chemistry, 2013
Direct conversion of methane to ethylene, acetylene, and synthesis gas at ambient pressure and temperature in a parallel plate discharge reactor was investigated.
Mohammad Ali Khodagholi, Mohammad Irani
doaj   +1 more source

Ecofriendly Natural Surfactants in the Oil and Gas Industry: A Comprehensive Review. [PDF]

open access: yesACS Omega, 2023
Abdurrahman M   +6 more
europepmc   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Intelligent prediction method and application of single-well in-situ stress in shale reservoirs driven by multi-source data

open access: yesDizhi lixue xuebao
Objective  Deep shale reservoirs are characterized by high temperature, high pressure, elevated in situ stress, and strong plasticity. Conventional in-situ stress testing methods and log interpretation models, often calibrated under simplified laboratory
SHEN Baojian   +9 more
doaj   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

open access: yesAdvanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca   +9 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy