Results 21 to 30 of about 5,653 (264)

Analysis of Chaotic Features in Dry Gas Seal Friction State Using Acoustic Emission

Lubricants
In this study, a chaos theory-based characterization method is proposed to address the nonlinear behavior of acoustic emission (AE) signals during the startup and shutdown phases of dry gas seals. AE signals were collected through a controlled experiment
Shuai Zhang, Xuexing Ding, Jinlin Chen, Shipeng Wang, Lanxia Zhang   +4 more
doaj   +1 more source

Features of test of air-fuel system of gas turbine engine [PDF]

Омский научный вестник: Серия "Авиационно-ракетное и энергетическое машиностроение", 2018
The article is devoted to the problem of ensuring the operability of rotary bearings of a gas turbine engine (GTE) with an air-fuel lubrication system.
V. N. Klimov, D. Ya. Dud’ev, V. Ya. Sigaylo, N. I. Klimov   +3 more
doaj   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Advanced Head Disk Interface System Assisted by Gas PFPE Lubrication

Tribology Online, 2011
An advanced head disk interface (HDI) system assisted by gas perfluoropolyether (PFPE) lubrication is discussed in this paper. It is known that lubricant spins off at a high rotation speed and high temperature.
Hiroyuki Matsumoto, Hiroshi Tani
doaj   +1 more source

Comparison of fluctuations and micro-vibration of the aerostatic bearing with the multi-hole integrated restrictor

Advances in Mechanical Engineering, 2022
In order to research the lubrication characteristics of various restrictors on the aerostatic bearing, an aerostatic bearing with the multi-hole integrated restrictor (MIR) was proposed in this paper.
Zhiwei Lu, Xiyao Liu, Bo Liu, Junan Zhang   +3 more
doaj   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Flow Characteristics and Experimental Verification of T-Groove Dry Gas Seal Under Different Flow States

Lubricants
With the improvement of dry gas seal efficiency in high-parameter fields, the flow pattern of gas film lubrication is complicated. Based on gas lubrication theory, the Reynolds equation of compressible gas was established with a bidirectional T-groove ...
Lanxia Zhang, Xuexing Ding, Shipeng Wang, Shuai Zhang   +3 more
doaj   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Overlapping layers in a gas lubrication problem

Journal of Computational and Applied Mathematics, 2004
zbMATH Open Web Interface contents unavailable due to conflicting licenses.
Aliu, E., Shepherd, J.J.
openaire   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source