Results 81 to 90 of about 7,511 (249)
steel research international, EarlyView.In this study, the susceptibility to copper‐induced hot shortness of the alloy 42CrMo4 is investigated by different hot tensile tests, as well as by a detailed analysis of the formed oxidation products. While an enrichment of metallic copper and a penetration of the grain boundaries are observed, no critical reduction of the tensile test properties can
Alexander Gramlich +6 more
wiley +1 more source
Evaluation of Melting Efficiency in Cold Wire Gas Metal Arc Welding Using 1020 Steel as Substrate
MetalsA key welding parameter to quantify in the welding process is the ratio of the heat required to melt the weld metal versus the total energy delivered to the weld, and this is referred to as the melting efficiency.
R. A. Ribeiro +2 more
doaj +1 more source
Influence of Higher Tramp Element Level on the Weldability of Automotive Steels
steel research international, EarlyView.The use of green recycled steels is constantly expanding in the automotive industry. The increase in tramp elements resulting from the recycling of steel is problematic. Tramp elements can lead to a negative influence on the weldability. To understand the influence, the welding properties of three green steels are characterized. The potential limits of
Elias Gebhard Vogt +6 more
wiley +1 more source
Laser assisted arc welding process for dry hyperbaric deep water application [PDF]
, 2013 Hyperbaric Gas Metal Arc Welding (GMAW) is an important technology for repair welding of deep sea pipelines and linking of existing pipeline networks to newer ones through tie-ins and hot-tap welding.
Ofem, Usani Unoh
core
steel research international, EarlyView.This study validates a recycling pathway for converting interconnect assemblies from end‐of‐life SOC stacks into commercial‐grade AISI 304 steels. Using scrap‐based steelmaking operations, austenitic cast steels with <4.0% δ‐ferrite are successfully produced.
Jeraldine Lastam +7 more
wiley +1 more source
Welding of X100 linepipe [PDF]
, 2004 The benefits of high strength steels in terms of reduced material volume due to enhanced mechanical performance have been known for some time. Large diameter transmission linepipe steels of minimum 690MPa ('XIOO') yield strength have been developed ...
Hudson, Mark G.
core
steel research international, EarlyView.The study investigates the influence of DED‐Arc/M versus casting on the microstructure and material properties of X40CrMoV5‐1 (AISI H13) hot‐work tool steel. DED‐Arc/M yields finer microstructures, superior mechanical strength, and ductility, but slightly reduced thermal conductivity.
Ulf Ziesing +4 more
wiley +1 more source
Defence Technology, 2019 This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels. The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting ...
Wichan Chuaiphan +1 more
doaj +1 more source
steel research international, EarlyView.Prebending of 304L/Q345R cladded plates significantly alters the subsequent weld thermal cycle and modifies the local interfacial microstructure. Combined electron backscatter diffraction (EBSD) and microscopy analysis demonstrates that deformation twinning, martensitic transformation, and defect initiation are concentrated at the trimaterial junction,
Ali Fahem +2 more
wiley +1 more source
Welding process impact on residual stress and distortion [PDF]
, 2009 Residual stress and distortion continue to be important issues in shipbuilding and are still subject to large amounts of research. This paper demonstrates how the type of welding process influences the amount of distortion.
Colegrove, Paul A. +10 more
core +1 more source