Results 81 to 90 of about 2,556,373 (288)
Advanced Engineering Materials, EarlyView.Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt +5 more
wiley +1 more source
Nauka ta progres transportu, 2018 Purpose. The main purpose of the article is calculation of spatial distribution fields of the conditional probability of lethal damage to the railway station personnel, caused by the inhalation of toxic gas, which is dissipated in the surface layer of ...
Y. O. Skob, M. L. Ugryumov
doaj +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Applying Improved Electrical Breakdown Model to Study Insulating Property of c-C4F8/N2 Gas Mixture
Gaoya dianqi, 2011 Perfluorocyclobutane(c-C4F8) has been recently considered as a potential alternative to SF6,because of its high electro-negativity and extremely low environmental effect.However,due to its high boiling point,c-C4F8 should mixed with buffer gases such as ...
doaj
Advanced Engineering Materials, EarlyView.Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
Mokslas: Lietuvos Ateitis, 2019 The hot dip galvanizing process is the most popular long-term corrosion protection method for welded constructions. The article analyzes influence of shielding gas by reducing the zinc layer on the seams in MAG welding.
Justė Rožėnė +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar +3 more
wiley +1 more source
Experimental study on the partial discharge and AC breakdown properties of C(4)F(7)N/CO(2) mixture
High Voltage, 2019 As an environmental friendly insulating medium, C(4)F(7)N has received extensive attention in the past two years. In this study, the partial discharge (PD) and breakdown characteristics of C(4)F(7)N/CO(2) gas mixture were investigated using the gas ...
Yi Li +8 more
doaj +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Advanced Engineering Materials, EarlyView.Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source