Results 71 to 80 of about 4,775,034 (345)

NO gas sensor based on ZnGa2O4 epilayer grown by metalorganic chemical vapor deposition

Scientific Reports, 2019
A gas sensor based on a ZnGa2O4(ZGO) thin film grown by metalorganic chemical vapor deposition operated under the different temperature from 25 °C to 300 °C is investigated in this study. This sensor shows great sensing properties at 300 °C.
M. Wu, Wei-Zhong Li, Chun-Yi Tung, Chiung-Yi Huang, Yi-Hung Chiang, Po-Liang Liu, R. Horng   +6 more
semanticscholar   +1 more source

Hydrogel‐Based Capacitive Sensor Model for Ammonium Monitoring in Aquaculture

Advanced Engineering Materials, EarlyView.
Traditional techniques for monitoring aquaculture water quality, particularly ammonium levels, harm fish. This work presents a novel capacitive sensor with an ionic hydrogel transducer to monitor ammonium concentration in real time based on the ammonium‐induced hydrogel dissociation and osmotic pressure. Monitoring aquaculture water quality, especially
Mohammad Mirzaee, Mahdi Askari‐sedeh, Ali Zolfagharian, Mostafa Baghani   +3 more
wiley   +1 more source

RGO/CuCl-Based Flexible Gas Sensor for High-Concentration Carbon Monoxide Gas Detection at Room Temperature

Micromachines
Carbon monoxide (CO) gas sensors are widely used, especially for environmental monitoring in confined spaces such as the landscape of mining cave ruins in mining parks, which is essential for ensuring the health and safety of tourists and staff.
Qingqing Liu, Fuzheng Zhang, Mengfei Pei, Weile Jiang   +3 more
doaj   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Development of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness

Advanced Engineering Materials, EarlyView.
Additive manufacturing of magnesium alloys by laser is difficult because the melting point of the oxide layer is much higher than the evaporation temperature of the metal underneath. Making the oxide layer thinner can solve this problem. Alloying magnesium with strontium makes the oxide layer thinner, especially at 0.5 wt%.
Elmar Jonas Breitbach, Stefan Julmi, Sabine Behrens, Tatiana Blank, Arvid Abel, Nicole Emminghaus, Ludger Overmeyer, Christian Klose, Hans Jürgen Maier   +8 more
wiley   +1 more source

Mechanisms of Increasing Weld Depth during Temporal Power Modulation in High‐Power Laser Beam Welding

Advanced Engineering Materials, EarlyView.
Temporal power modulation increases weld depth in high‐power laser beam welding of dissimilar round bars by nearly 20% compared to same average continuously welded welding power. The mechanism of action also applies to sheet welding and depends on the inertia of keyhole depth for the modulated laser beam power.
Jan Grajczak, David Reynders, Christian Nowroth, Jens Twiefel, Jörg Wallaschek, Sarah Nothdurft, Jörg Hermsdorf, Stefan Kaierle   +7 more
wiley   +1 more source

Design and Implementation of a WSN-based Monitoring System for Hazardous Gas in Chemical Production

Chemical Engineering Transactions, 2017
Hazard gases generated during chemical production process pose great risks to personal and property safety, and only rapid monitoring of hazardous gas can ensure the safety of the production process.
Chaoqing Mao
doaj   +1 more source

From Damage to Functionality: Remanufacturing of Thrust Roller Bearings by Tailored Forming

Advanced Engineering Materials, EarlyView.
Herein, the wear and fatigue behavior of repaired bearing raceways with a new powder alloy is investigated using a FE8 test‐rig and an oscillating tribometer. The tests are compared with industrial manufactured bearings to evaluate the repair quality. The repair can extend the service life of the repaired bearing to that of a new bearing and improves ...
Felix Saure, Florian Pape, Gerhard Poll, Max Marian   +3 more
wiley   +1 more source

Proton-Conductive Gas sensor: A New Way to Realize Highly Selective Ammonia Detection for Analysis of Exhaled Human Breath.

ACS Sensors, 2019
The analysis of exhaled human breath has great significance for early noninvasive diagnosis. A poor selectivity and strong humidity influence are two bottlenecks for the application of gas sensors to exhaled breath analysis. In this work, we utilized the
Hongran Zhao, Lichao Liu, Xiuzhu Lin, Jianxun Dai, Sen Liu, Teng Fei, Tong Zhang   +6 more
semanticscholar   +1 more source

Simulation of Inhomogeneous Refractive Index Fields Induced by Hot Tailored Forming Components

Advanced Engineering Materials, EarlyView.
This article presents a simulation model for simulating inhomogeneous refractive index fields (IRIF) in hot‐forged components, accounting for thermal influences and complex geometries. Through this simulation, a priori knowledge about the propagation of the IRIF can be obtained, allowing for the positioning of the component or an optical measurement ...
Pascal Kern, Lennart Hinz, Markus Kästner, Eduard Reithmeier   +3 more
wiley   +1 more source