Results 231 to 240 of about 4,579 (296)

Psychometric Considerations in Assessing Fear Generalization as a Predictor of Anxiety. [PDF]

Biol Psychiatry Glob Open Sci
Stegmann Y, Reutter M, Hutterer K, Hildebrandt L, Deckert J, Deserno L, Domschke K, Lonsdorf TB, Pauli P, Reif A, Rosenkranz K, Schiele MA, Schümann D, Zwanzger P, Andreatta M, Gamer M.   +15 more
europepmc   +1 more source

A note on the Gauss curvature of harmonic and minimal surfaces [PDF]

Pacific Journal of Mathematics, 1982
openaire   +3 more sources

Quality Control of Magnetotelluric Impedance Inversion via Self‐Supervised Learning Based on Data Continuity of Nyquist Diagrams

Geophysical Prospecting, Volume 74, Issue 5, June 2026.
ABSTRACT Magnetotelluric (MT) data are often contaminated by electromagnetic (EM) noise, making quality control (QC) essential for reliable inversion. Conventional manual time‐domain QC processes are labour‐intensive, and some noise inevitably remains after processing, necessitating complementary processing in the frequency domain to address the ...
Hanjoon Park, Hee June Lee, Jun‐Woo Lee, Janghwan Uhm, Junyeong Heo, Dong‐Joo Min   +5 more
wiley   +1 more source

Comparative Assessment of Graglia-Wilton-Peterson and Rao-Wilton-Glisson Basis Functions for Radiofrequency Coil Modeling in Magnetic Resonance Imaging. [PDF]

IEEE J Multiscale Multiphys Comput Tech
Franzò D, Giannakopoulos II, Merlini A, Andriulli F, Lattanzi R.   +4 more
europepmc   +1 more source

High Cycle Fatigue Properties of PM‐HIPed High‐Nitrogen Tool Steel: Effect of Surface Condition

Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2097-2115, June 2026.
ABSTRACT This study explores the impact of surface condition on high‐cycle fatigue performance of a high‐nitrogen martensitic tool steel manufactured through powder metallurgy and hot isostatic pressing. In near‐net manufacturing applications, acid‐leaching pickling treatment and/or machining is used as a post‐treatment to remove the powder container ...
Faezeh Javadzadeh Kalahroudi, Dimitrios Nikas, Giulio Maistro, Mikael Grehk   +3 more
wiley   +1 more source

Targetless LiDAR-camera extrinsic calibration via semantic distribution alignment. [PDF]

Front Robot AI
Chen X, Sun B.
europepmc   +1 more source

Machining Simulation of Recrystallized SiC: Failure Mechanisms, Numerical Influences, Tool Dynamics, and Friction Behavior

Journal of the American Ceramic Society, Volume 109, Issue 6, June 2026.
ABSTRACT This paper presents a comprehensive study on the machining simulation of recrystallized silicon carbide (R‐SiC), with a focus on material failure mechanisms, numerical influences, tool kinematics, and frictional behavior. A representative volume of interest was derived from CT data, and a meshing algorithm for CT‐based structures was ...
Simon Unseld, Stefan Kleiner, Achim Rösiger, Ralf Goller, Dietmar Koch   +4 more
wiley   +1 more source

Optimal interpolation methods for predicting groundwater levels in Abu Dhabi Emirate using ArcGIS. [PDF]

Sci Rep
Maksoud T, Alkhawaga A, Mohamed M.
europepmc   +1 more source

High‐Accuracy Thin‐Film Stress Sensor Exploiting Integrated Digital Image Correlation

Strain, Volume 62, Issue 3, June 2026.
A high‐accuracy Speckle Stress Sensor (SSS) is introduced for real‐time thin‐film stress measurements, combining integrated digital image correlation (IDIC) with dense overlapping spot patterns generated by a simple LED‐perforated plate setup. Unlike conventional multi‐beam optical stress sensors relying on detection of the centers of isolated laser ...
R. F. M. Martens, O. van der Sluis, M. G. D. Geers, J. P. M. Hoefnagels   +3 more
wiley   +1 more source

An adaptive slicing algorithm based on model contour information. [PDF]

PLoS One
Han X, Liu X, Lu K, Cui L.
europepmc   +1 more source