Results 161 to 170 of about 75,878 (214)

A Practical Identifiability Criterion Leveraging Weak-Form Parameter Estimation. [PDF]

Bull Math Biol
Heitzman-Breen N, Dukic V, Bortz DM.
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Critical review of patient outcome study in head and neck cancer radiotherapy. [PDF]

Meta Radiol
Chen J, Yang Y, Liu C, Feng H, Holmes J, Zhang L, Frank S, Simone CB, Ma DJ, Patel SH, Liu W.   +10 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Weighted quantile sum (WQS) mixed-effects model. [PDF]

MethodsX
Gennings C, Midya V, Renzetti S, DeFelice N.   +3 more
europepmc   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Age-Related Associations of Foveal Structural Parameters in Healthy Adults: A Comparative Analysis of Biological and Chronological Age. [PDF]

Vision (Basel)
Khalatyan AS, Yusef Y, Altemirova KK, Machekhina LV, Melnitskaya AA, Strazhesko ID.   +5 more
europepmc   +1 more source

Analyzing Electronic Excitations and Exciton Binding Energies in Y6 Films

Advanced Functional Materials, EarlyView.
The Y6 molecule is used for increasing the efficiency of organic solar cells. The exciton binding energy is calculated for ensembles of Y6 molecules that are representative of the typically used films. The calculations show that the excitons typically spread out over many molecules.
Sahar Javaid Akram, Sophie Meißner, Stephan Kümmel   +2 more
wiley   +1 more source

Design and analysis of individually randomized multiple baseline factorial trials. [PDF]

Behav Res Methods
Ouyang Y, Avila ML, Heath A.
europepmc   +1 more source