Results 71 to 80 of about 693,780 (338)
Geometric Self-Calibration of YaoGan-13 Images Using Multiple Overlapping Images
Sensors, 2019 Geometric calibration is an important means of improving the absolute positioning accuracy of space-borne synthetic aperture radar imagery. The conventional calibration method is based on a calibration field, which is simple and convenient, but requires ...
Guo Zhang +3 more
doaj +1 more source
LEICA DMC III CALIBRATION AND GEOMETRIC SENSOR ACCURACY [PDF]
The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences, 2016 As an evolution of the successful DMC II digital camera series, Leica Geosystems has introduced the Leica DMC III digital aerial camera using, for the first time in the industry, a large-format CMOS sensor as a panchromatic high-resolution camera head ...
C. Mueller, K. Neumann
doaj +1 more source
Algorithms for fitting cylindrical objects to sparse range point clouds for rapid workspace modeling [PDF]
, 2003 Current methods for construction site modeling employ large, expensive laser range scanners that produce dense range point clouds of a scene from different perspectives.
Bosché, Frédéric +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Enhancing Printability Through Design Feature Analysis for 3D Food Printing Process Optimization
Applied SciencesWe present a novel, systematic method for evaluating design printability in 3D food printing using a scoring system based on the Design for Additive Manufacturing (DfAM) guidelines.
Mohammed Alghamdy +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Analysis of the Geometric Accuracy of Wax Models Produced Using PolyJet Molds
Tehnički GlasnikThe article presents an analysis of the geometric accuracy of wax models produced using PolyJet molds. Photopolymer resin was used to make the molds, and the surface of the model was finished in a gloss mode in the 3D printing process. This allows you to
Mariusz Cygnar +6 more
doaj +1 more source